Second round of tools for April. Pickings have been fairly good so far
for the month and there are some great fresh tools on the list this
time. Get them while they are hot (not THAT kinda hot..!!)
PayPal is preferred (if you use it) on all items. It's easier for me to
ship items off of a paid PayPal invoice, especially First Class ones.
Checks and money orders are still welcome.
And remember........da more ya buy, the cheaper they fly!
First contact (that is e-mail, or phone) that says I want it gets it.
Prices do not include shipping. All items are shipped with Delivery
Confirmation. Insurance, unless it is a big order or a very fragile item
is optional. Just let me know. Also, I am shipping a lot more stuff via
First Class mail. There will be a small amount added to the shipping
cover the cost of the padded mailer. I don't get them for free.
Please put your name and address in the message. Saves time and email
traffic!
------------------------------------------------------
SEVEN G I Mix No 1 EX Paring Bevel Side Chisels. There is a 3/4",
measuring 8 13/16" from the edge to the end of the socket, the blade is
6 1/8" long, a 7/8", measuring 9 3/16" from the edge to the end of the
socket, the blade is 6 1/8" long, a 1", measuring 9 1/16" from the edge
to the end of the socket, the blade is 6 1/8" long, a 1 1/4", measuring
9 1/2" from the edge to the end of the socket, the blade is 6" long, a 1
1/2", measuring 10 1/8" from the edge to the end of the socket, the
blade is 6 3/16" long, a 1 3/4", measuring 10 1/8" from the edge to the
end of the socket, the blade is 6 1/4" long, a 2", measuring 10 1/8"
from the edge to the end of the socket, the blade is 6 1/4" long, and
they weigh 4 lbs 5 oz unboxed. These are in reasonably good condition
and were cleaned. The backs have a few spots of very light pitting,
along with some staining and frosting, but overall nothing too bad. The
tops have more of the same. The edges are fairly good, but will need a
little work. I did take off a little sharp mushrooming off of a couple
of the sockets, and the one is a little funky on the inside where
somebody else got aggressive removing an old handle, but they are good.
These will need handles, I've tried to get a nice matching set together
with no luck. These ain't pristine, but they sure ain't bad, and sets
like this are getting few and very far between of late. The price
includes US Priority Mail Shipping with insurance and signature
confirmation. $375.00
http://oldetoolshop.com/forsale/april/chiselset0401a.jpg
http://oldetoolshop.com/forsale/april/chiselset0401b.jpg
http://oldetoolshop.com/forsale/april/chiselset0401c.jpg
http://oldetoolshop.com/forsale/april/chiselset0401d.jpg
http://oldetoolshop.com/forsale/april/chiselset0401e.jpg
http://oldetoolshop.com/forsale/april/chiselset0401f.jpg
Vintage Oyster Clam Shucker Shucking Tool From A Kearney & Foot File.
Measuring 7 7/8" long and this weighs 8 oz unboxed. Kearney & Foot were
US file makers in business until 1901 when they were acquired by
Nicholson who continued the mark. This is in decent condition and was
cleaned. There is a little pitting on the head, but the edges are
good. The handle area is good. This is a neat and collectible one as
well. $24.00
http://oldetoolshop.com/forsale/april/clamknife0401a.jpg
http://oldetoolshop.com/forsale/april/clamknife0401b.jpg
Forged 1 lb Cross Peen Hammer Head. Measuring 4" long, the face is 1"
in diameter, the peen is 1 1/16" wide, and this weighs 15 3/4 oz
unboxed. Not signed as to the maker. This is in decent condition and
was cleaned. There is some overall light pitting and patina on the
head. The face has a ding in the center and the start of some
mushrooming. The peen and eye are good to go. This ain't perfect, but
drop it on a handle, and it will get the job done. $18.00
http://oldetoolshop.com/forsale/april/hammer0402a.jpg
http://oldetoolshop.com/forsale/april/hammer0402b.jpg
http://oldetoolshop.com/forsale/april/hammer0402c.jpg
http://oldetoolshop.com/forsale/april/hammer0402d.jpg
Kinex DIN 875/0 4 Inch Machinist Square. Measuring 5 1/8" overall in
length, the blade is 4 1/16" long, 3 3/32" high, and this weighs 8 oz
unboxed. This is in very good condition and was not cleaned. There are
some light scuffs and a few dots of light patina, but nothing too bad.
The edges and corners are crispy good. This is a quality tool and
priced cheaper than what a new one will run you. $30.00
http://oldetoolshop.com/forsale/april/machinisttool0405a.jpg
http://oldetoolshop.com/forsale/april/machinisttool0405b.jpg
http://oldetoolshop.com/forsale/april/machinisttool0405c.jpg
G A Benton Chelsea MA Side Rabbet Molding Plane. Measuring 9 1/2" long
and this weighs 7 3/4 oz unboxed. George A Benton was a Chelsea MA
plane maker who worked from 1855 until 1872. This is the C mark which
is rated 3 "***" for rarity. This is in decent condition and was
cleaned. The body has some stains, dings, and somebody drilled holes to
use this with a plow plane fence for some reason. There is a little
wear to the back down at the sole. The mouth isn't super tight, but it
was never messed with. The W Butcher iron is clean, but the edge is a
little uneven. The wedge has a little chipping on the top. This ain't
perfect, but side rabbet planes are sure not very common to say the
least. $32.00
http://oldetoolshop.com/forsale/april/woodenplane0403a.jpg
http://oldetoolshop.com/forsale/april/woodenplane0403b.jpg
http://oldetoolshop.com/forsale/april/woodenplane0403c.jpg
http://oldetoolshop.com/forsale/april/woodenplane0403d.jpg
Unusual Long Wood Model Makers Clamp. The body is 15 7/8" overall, the
clamping area is 13 1/2" long, the throat is 1/2", the holes for the
movable jaw are spaced at 7/8", and this weighs 3 1/2 oz unboxed. Not
signed as to the maker. This is in reasonably good condition and was
cleaned. There are some light dings and stains, but nothing too bad.
The screw travels the full distance. All the holes are clear. This is
a neat clamp for doing light work to say the least. $24.00
http://oldetoolshop.com/forsale/april/clamp0402a.jpg
http://oldetoolshop.com/forsale/april/clamp0402b.jpg
http://oldetoolshop.com/forsale/april/clamp0402c.jpg
Stanley No 18 6 Inch 1908 Patent Eureka Bevel Square. This weighs 6 oz
unboxed. Christian Bodmer of New Britain, CT was granted Pat. No.
893,223 on July 14, 1908 for the design of this tool. This is in decent
condition and was cleaned. There are some spots on the handle where the
plating is gone, but most of it is present. The blade has some stained
spots, but the edges and corners are good. Both screws work and were
oiled, but the blade does stick a little coming in and out of the body.
This ain't minty, but it will get the job done. $24.00
http://oldetoolshop.com/forsale/april/square0401a.jpg
http://oldetoolshop.com/forsale/april/square0401b.jpg
http://oldetoolshop.com/forsale/april/square0401c.jpg
http://oldetoolshop.com/forsale/april/square0401d.jpg
T H Witherby 7/16 Inch Socket Bench Gouge. Measuring 8 1/16" from the
edge to the end of the socket, the blade is 5 5/8" long, 7/16" wide
across the outside of the sweep, this is 12 5/8" overall, and this
weighs 4 1/2 oz unboxed. The mark is partial and faint. This is in
reasonably good condition and was cleaned. The back of the sweep is
good save for a little staining as is the inside. The edge is sharp.
The socket is good and was never hit. The handle has some stains and 3
small user notches on the side, but it's good to go. This is a top
quality tool that will get the job done. $24.00
http://oldetoolshop.com/forsale/april/chisel0402a.jpg
http://oldetoolshop.com/forsale/april/chisel0402b.jpg
http://oldetoolshop.com/forsale/april/chisel0402c.jpg
Lufkin Rule No 513 Micrometer Depth Gage With Orig Box. This all weighs
1 lb unboxed. John A. Schleicher of Saginaw, MI was granted Pat. No.
1,424,383 on Aug. 1, 1922 and Pat. No. 1,568,295 on Jan. 5, 1926 for the
design of this tool. This is in good condition and was not cleaned.
The head is clean save for some very light scratches on the face and
some light scuffs on the back. The micrometer turns smoothly and the
cap nut for the rods works. This has 3 rods total (one in the tool and
2 in the box). They have a little wear on the sides, but nothing too
bad. This also has the wrench. The oak box has some dings and light
stains, but it's solid, and the late works. This ain't pristine, but it
will get the job done. $45.00
http://oldetoolshop.com/forsale/april/machinisttool0403a.jpg
http://oldetoolshop.com/forsale/april/machinisttool0403b.jpg
http://oldetoolshop.com/forsale/april/machinisttool0403c.jpg
http://oldetoolshop.com/forsale/april/machinisttool0403d.jpg
http://oldetoolshop.com/forsale/april/machinisttool0403e.jpg
http://oldetoolshop.com/forsale/april/machinisttool0403f.jpg
One PAIR Hields Nottingham No 12 Skew Hollow & Round Molding Planes.
The cut is 3/4" (straight across), and they weigh 1 lb 6 3/4 oz
unboxed. William Hields was a Nottingham England plane maker who worked
from 1830 until 1885. The irons are bedded at York pitch and are
skewed. These are in reasonably good condition and were cleaned. The
bodies have some light dings and stains. The soles are good, although
there are some light dings along the side edges of the hollow. Both
mouths are good. Both of the irons have some small spots of pitting,
but are clean for the most part. The edges will need a touch up. Both
wedges have some dings. These ain't pristine, but they will get the job
done. $45.00
http://oldetoolshop.com/forsale/april/woodenplane0402a.jpg
http://oldetoolshop.com/forsale/april/woodenplane0402b.jpg
http://oldetoolshop.com/forsale/april/woodenplane0402c.jpg
http://oldetoolshop.com/forsale/april/woodenplane0402d.jpg
http://oldetoolshop.com/forsale/april/woodenplane0402e.jpg
http://oldetoolshop.com/forsale/april/woodenplane0402f.jpg
Sears By Greenlee 10 Inch Draw Knife Or Drawknife. Measuring 15 1/2"
overall, the blade is 10" long, 1 7/16" wide across the edge, and this
weighs 1 lb 4 oz unboxed. This is in reasonably good condition and was
cleaned. The back is clean save for one very small and light patch of
pitting. There is a larger spot of light pitting on the front. The
edge is good and the top was never hit. The handles have some dings and
stains, but have all of the original finish. The ferrules and end caps
have some light patina. This ain't minty, but it's a quality tool that
will get the job done. $45.00
http://oldetoolshop.com/forsale/april/drawknife0401a.jpg
http://oldetoolshop.com/forsale/april/drawknife0401b.jpg
http://oldetoolshop.com/forsale/april/drawknife0401c.jpg
Vintage Tinsmith Panel Or Paneling Hammer. Measuring 11 1/4" overall,
the head is 4 1/4" long, the face is a little under 3/4" square, the
peen is 3/4" wide, and this weighs 10 1/2 oz unboxed. Not signed as to
the maker. This is in decent condition and was cleaned. There are some
spots of light pitting and some overall frosting on the head, along with
user initials on the one side. The face has some tiny dings, but
nothing too bad. The peen is good. The handle has a check under the eye
from the wedge and some stains, but it's solid. This ain't perfect, but
it will get the job done. $18.00
http://oldetoolshop.com/forsale/mar/hammer0304a.jpg
http://oldetoolshop.com/forsale/mar/hammer0304b.jpg
http://oldetoolshop.com/forsale/mar/hammer0304c.jpg
http://oldetoolshop.com/forsale/mar/hammer0304d.jpg
Essex Mfg Co 5/8 Inch Bevel Side Paring Chisel. Measuring 8 13/16" from
the edge to the end of the socket, the blade is 6 1/8" long, this is 12
9/16" overall, and this weighs 6 1/4 oz unboxed. This is in reasonably
good condition and was cleaned. The back is good save for some light
scuffs and a little frosting. The top has some stained spots, but
nothing too bad. The edge has some chipping and will need a touch up.
The socket is good. The handle is a good replacement and is good other
than a little staining on the one side. This ain't pristine, but it's a
solid tool that will get the job done. $20.00
http://oldetoolshop.com/forsale/mar/chisel0305a.jpg
http://oldetoolshop.com/forsale/mar/chisel0305b.jpg
http://oldetoolshop.com/forsale/mar/chisel0305c.jpg
Vintage 6 Inch Wing Compass Or Divider. Measuring 6 3/16" long and this
weighs 4 1/4 oz unboxed. Not signed as to the maker, other than the
Made In USA mark. This is a probably a Wm Johnson. This is in
reasonably good condition and was cleaned. There is some frosting and a
few small spots of light pitting. The joint and tips are good. The
locking screw and fine adjuster nut both work and were oiled. This
ain't pristine, but it will get the job done. $17.00
http://oldetoolshop.com/forsale/mar/divider0301a.jpg
http://oldetoolshop.com/forsale/mar/divider0301b.jpg
http://oldetoolshop.com/forsale/mar/divider0301c.jpg
Springfield Trapdoor Model 1879 Gun Tool. Measuring 2 5/8" long and
this weighs 1 1/4 oz unboxed. This is in reasonably good condition, the
only cleaning was a wipe down with some penetrating oil to get rid of
some grease. There is a little overall light patina and some oil
residue. The joint is good and hold except for one small area. The
wrench, punch, and screwdriver tips are all good to go. This ain't
minty, but it will get the job done. $17.00
http://oldetoolshop.com/forsale/mar/guntool0302a.jpg
http://oldetoolshop.com/forsale/mar/guntool0302b.jpg
http://oldetoolshop.com/forsale/mar/guntool0302c.jpg
FIVE C Maier Carving Tools. There is a 1/8" and a 1/4" skew chisel, a
3/32" V-gouge, a 5/16" and 7/16" fishtail gouge and they weigh 2 oz
unboxed. C. Maier & Sons were a Newark NJ tool maker, they started in
the 1800's and were around until the 1920's, but not a lot is known
about the company. These are in reasonably good condition and were
cleaned by someone else. There ain't much in the way of patina to fuss
about. A couple of the edges will need a little touch up. These will
need handles, but that is easy enough to do. Maier carving tools are
known for their quality and their smaller sizes make these ideal for
detail work. $65.00
http://oldetoolshop.com/forsale/mar/carvingtool0303a.jpg
http://oldetoolshop.com/forsale/mar/carvingtool0303b.jpg
http://oldetoolshop.com/forsale/mar/carvingtool0303c.jpg
http://oldetoolshop.com/forsale/mar/carvingtool0303d.jpg
L & I J White 11/16 Inch Bench Gouge. Measuring 5 7/8" from the edge to
the top of the handle, the blade is 4 3/8" long, 11/16" wide across the
inside of the sweep, 13/16" across the outside, this is 11 1/12"
overall, and this weighs 5 1/2 oz unboxed. L. & I. J. White were
Buffalo NY toolmakers who were in business from 1837 until 1928. This
is in reasonably good condition and was cleaned. The inside of the sweep
is clean other than a light patch of pitting around the center. The
back has some stained spots, but nothing too bad. The edge is wicked
good. The London pattern handle looks to be apple wood. That has some
dings, stains, and a couple of small chips, but it's solid. This ain't
pristine, but it's a quality tool that will get the job done. $27.00
http://oldetoolshop.com/forsale/mar/chisel0302a.jpg
http://oldetoolshop.com/forsale/mar/chisel0302b.jpg
http://oldetoolshop.com/forsale/mar/chisel0302c.jpg
Early Rosewood & Brass 2 ft Folding Rule. The body is 12 3/8" long and
this weighs 1 3/4 oz unboxed. Not signed as to the maker, but this
could be 18th or early 19th Century as to the age. This is in good
condition and was cleaned at some point, but not by me. The body has
some light stains and is missing a few of the tiny brass pins, but
nearly all of them are present. There are also hand stamped numerals as
well. NOW, an inch on this guy is actually 15/16", but that has varied
a lot over the years. There is a very slight outward bow to both
sections looking from the slot. The brass rule is good save for some
wear to the corners. The joint is fairly good, but does get a little
loose with the brass straight out. I gotta say that rules like this are
few and very far between. $160.00
http://oldetoolshop.com/forsale/mar/earlyrule0301a.jpg
http://oldetoolshop.com/forsale/mar/earlyrule0301b.jpg
http://oldetoolshop.com/forsale/mar/earlyrule0301c.jpg
http://oldetoolshop.com/forsale/mar/earlyrule0301d.jpg
Maples & Sons Cast Steel No 5 11/16" Carving Tool Gouge. Measuring 5"
from the edge to the top of where the handle would start, the blade is
11/16" wide across the sweep, the sweep looks to be a No. 5, this is 7
1/4" overall, and this weighs 2 oz unboxed. This is in fair condition
and was cleaned. Somebody else had polished the sweep a little at the
edge, but after that there is some overall light pitting on the inside.
The back is fairly clean for the most part. The tang is good. This
will need a handle. This ain't perfect, but with a little work, it will
get the job done. $14.00
http://oldetoolshop.com/forsale/mar/carvingtool0301a.jpg
http://oldetoolshop.com/forsale/mar/carvingtool0301b.jpg
http://oldetoolshop.com/forsale/mar/carvingtool0301c.jpg
Vintage Cobblers Hammer. Measuring 7 3/4" overall, the head is 3 5/8"
long, the face is 1 5/16" in diameter, the peen is 1 3/8" wide, and this
weighs 14 3/4 oz unboxed. Not signed as to the maker. This is in decent
condition and was cleaned. There is some overall roughness on the head
left over from when this was made. The black finish is original and
most of that is present. The face has some tiny dings, but nothing too
bad. The peen is good. The handle was user crafted and was hand carved
from a piece of oak. That has some checks at the end and some long gone
worm holes, but it's solid enough to use. This ain't pristine, but it
will get the job done. $17.00
http://oldetoolshop.com/forsale/mar/hammer0303a.jpg
http://oldetoolshop.com/forsale/mar/hammer0303b.jpg
http://oldetoolshop.com/forsale/mar/hammer0303c.jpg
http://oldetoolshop.com/forsale/mar/hammer0303d.jpg
Neat Small Cast Iron Novelty Ball Peen Hammer. Measuring 5 1/16"
overall, the head is 2 1/4" long, the face and peen are 7/16" in
diameter, and this weighs 4 3/4 oz unboxed. Not signed as to the
maker. This is in reasonably good condition and was not cleaned. There
are a few dots and small spots of patina, but this has almost all of the
original finish. The pictures tell the rest of the story. This is what
it is, but to my eye it is kinda neat. $14.00
http://oldetoolshop.com/forsale/mar/hammer0302a.jpg
http://oldetoolshop.com/forsale/mar/hammer0302b.jpg
http://oldetoolshop.com/forsale/mar/hammer0302c.jpg
http://oldetoolshop.com/forsale/mar/hammer0302d.jpg
Norton A500 IV Sharpening Stone. Measuring 7 1/2" long, 1 1/8" wide,
3/8" high, and this weighs 3 3/4 oz unboxed. The grit feels like a
fine. This is in good condition and was cleaned. There is some
staining on both sides, but nothing much in the way of wear. There are
some tiny dings on the sides. This ain't minty, but it is a quality
stone that will get the job done. $14.00
http://oldetoolshop.com/forsale/mar/sharpeningstone0301a.jpg
http://oldetoolshop.com/forsale/mar/sharpeningstone0301b.jpg
http://oldetoolshop.com/forsale/mar/sharpeningstone0301c.jpg
L S Starrett No 73 6 Inch Yankee Pattern Inside Caliper. Measuring 7"
long and this weighs 2 3/4 oz unboxed. This is in decent condition and
was cleaned. There is some light frosting on the legs and some light
pitting down by the tips. The spring and tips are good otherwise. The
nut travels the full distance and holds. This ain't pristine, but it
will get the job done. $16.00
http://oldetoolshop.com/forsale/mar/machinisttool0302a.jpg
http://oldetoolshop.com/forsale/mar/machinisttool0302b.jpg
http://oldetoolshop.com/forsale/mar/machinisttool0302c.jpg
Millers Falls No 3 Rogers Patent Timberframer T-Auger Handle. Measuring
16" long and this weighs 1 lb 4 1/4 oz unboxed. George E. Rogers of
Greenfield, MA was granted Pat. No. 484,050 on Oct. 11, 1892 for the
design of this tool. This isn't signed, but few of these were. This is
in reasonably good condition and was cleaned and the head refinished.
The jaws are good. The nut works and the threads were oiled. The oak
handles have some stains and dings, a few of them deep, but they are
solid and on tight. This ain't pristine, but it's a solid tool that
will get the job done. $45.00
http://oldetoolshop.com/forsale/mar/augerhandle0301a.jpg
http://oldetoolshop.com/forsale/mar/augerhandle0301b.jpg
http://oldetoolshop.com/forsale/mar/augerhandle0301c.jpg
http://oldetoolshop.com/forsale/mar/augerhandle0301d.jpg
Pexto Sampson-D No 8012D 12 Inch Sweep Brace. This weighs 3 lbs 5 1/4
oz unboxed. Henry V. Smith of Hartford, CT was granted Pat. No. 542,448
on July 9, 1895 for the original design of the chuck used on this tool.
This is in decent condition and was cleaned. The plating on the arms
and chuck is pretty much gone and there is some overall light frosting,
but nothing too bad patina wise. The Sampson chuck, which takes both
round shaft and square tang bits is good. The ratchet works in both
directions and the locked position. The grip and pad look to be
rosewood. They both have some dings, but spin freely. This ain't
pristine, but it's a solid and heavy duty tool that will get the job
done. $45.00
http://oldetoolshop.com/forsale/mar/brace0302a.jpg
http://oldetoolshop.com/forsale/mar/brace0302b.jpg
http://oldetoolshop.com/forsale/mar/brace0302c.jpg
http://oldetoolshop.com/forsale/mar/brace0302d.jpg
Stanley Handyman No H1253A 10 Inch Sweep Brace. This weighs 1 lb 15 1/4
oz unboxed. This is in reasonably good condition and was not cleaned.
There is some staining and a few spots of light patina on the frame, but
nothing too bad. The chuck and jaws are good, but this model never had
a spring on the jaws. The ratchet works in both directions and the
locked position. The wood grip and pad have almost all of the original
finish. There are a few dings and bits of paint, but both spin freely.
This ain't pristine, but it will get the job done. $24.00
http://oldetoolshop.com/forsale/mar/brace0301a.jpg
http://oldetoolshop.com/forsale/mar/brace0301b.jpg
http://oldetoolshop.com/forsale/mar/brace0301c.jpg
http://oldetoolshop.com/forsale/mar/brace0301d.jpg
Early Hand Forged Slater Slate Roofing Hammer. Measuring 13 1/8"
overall, the head is 7 9/16" long, the face is 5/8" in diameter, and
this weighs 1 lb 6 oz unboxed. Not signed as to the maker. This is in
decent condition and was cleaned. There is some overall roughness left
over from when this was made along with some bits of pitting and some
user added score lines. The face has some dings, a couple of tiny chips
around the edge, and the start of some mushrooming. The punch tip was
dressed recently and will need some fine tuning. This guy never had
nail claws. The breaking edge on the shaft is good. The wood handle
does have a couple of checks, but it's on tight. The nut at the end
does turn. This ain't minty, but it does have some history to it to say
the least. $32.00
http://oldetoolshop.com/forsale/feb/slatehammer0202a.jpg
http://oldetoolshop.com/forsale/feb/slatehammer0202b.jpg
http://oldetoolshop.com/forsale/feb/slatehammer0202c.jpg
http://oldetoolshop.com/forsale/feb/slatehammer0202d.jpg
Original CW Era Mainspring Vise. Measuring 1 11/16" high, the jaw is 2
3/8" long, and this weighs 2 1/2 oz unboxed. Not signed as to the
maker. This is in decent condition and was cleaned. There are some
spots of pitting on the body and jaw. The main screw works, that
travels the full distance and holds. The jaw also travels the full
distance, but the screw holding the jaw to the body, does not turn.
This ain't minty, but these guys are sure getting few and very far
between, and they ain't cheap when you do find one. Just saying. $65.00
http://oldetoolshop.com/forsale/feb/guntool0201a.jpg
http://oldetoolshop.com/forsale/feb/guntool0201b.jpg
http://oldetoolshop.com/forsale/feb/guntool0201c.jpg
http://oldetoolshop.com/forsale/feb/guntool0201d.jpg
C S Osborne No 33 Brass Head Magnetic Tack Hammer. Measuring 10 1/2"
overall, the head is 5 5/8" long, the face is 7/16" in diameter, the
peen is 5/16" in diameter, and this weighs 10 1/4 oz unboxed. This is
in good condition and was cleaned. There are some light dings on the
head. The face and peen have some staining, but nothing too bad patina
wise. The magnetic peen still has lots of stick to it. The handle is
original to the tool. That has almost all of the original finish plus a
coat of wax. The head wiggles a hair, but does no come off. This ain't
pristine, but it will get the job done. $23.00
http://oldetoolshop.com/forsale/feb/hammer0205a.jpg
http://oldetoolshop.com/forsale/feb/hammer0205b.jpg
http://oldetoolshop.com/forsale/feb/hammer0205c.jpg
http://oldetoolshop.com/forsale/feb/hammer0205d.jpg
Vintage 1/4 Inch Firmer Chisel. Measuring 4 1/2" from the edge to the
top of the handle, this is 10 11/16" overall, and this weighs 2 3/4 oz
unboxed. Not signed as to the maker, there is a user name stamped in a
few spots above the tang bolster. This is in reasonably good condition
and was cleaned. The back has some light scuffs and a few dots of
pitting, but overall nothing too bad. The sides and top also have some
light patina. The edge is ready to work. The oak handle has some dings
and stains, but it's solid. This ain't pristine, but it is a good
looking tool that will get the job done. $17.00
http://oldetoolshop.com/forsale/feb/chisel0204a.jpg
http://oldetoolshop.com/forsale/feb/chisel0204b.jpg
http://oldetoolshop.com/forsale/feb/chisel0204c.jpg
Vintage Cast Iron Hand Vise Or Handvise. Measuring 5" long, the jaws
are 1 7/16" wide, and this weighs 14 1/2 oz unboxed. This is signed,
but I can't read it. Might be a Dasco. This is in reasonably good
condition and was cleaned. There is some wear to the finish and bit of
patina, but overall nothing too bad. The jaws are good save for a wee
bit of chipping on the top. The cross hatching on the faces is also
good and they close up tight and flush. The screw is good and the nut
travels the full distance. The spring has lots of spring left to it.
This ain't pristine, but it will get the job done. $27.00
http://oldetoolshop.com/forsale/mar/handvise0201a.jpg
http://oldetoolshop.com/forsale/mar/handvise0201b.jpg
http://oldetoolshop.com/forsale/mar/handvise0201c.jpg
Lufkin No 8 Machinist Combination Square Ruler Clamp. This weighs 2 oz
unboxed. This is in good condition and was not cleaned. There ain't
nothing much patina wise to fuss about other than the initials on the
back (this probably was a school tool). All the screws work and the
tabs are good. There ain't much more to go wrong with one of these
guys. $18.00
http://oldetoolshop.com/forsale/feb/machinisttool0203a.jpg
http://oldetoolshop.com/forsale/feb/machinisttool0203b.jpg
http://oldetoolshop.com/forsale/feb/machinisttool0203c.jpg
Small Vintage 3 oz Cross Peen Hammer Head. Measuring 3 1/8" long, the
face is 9/16" square, the peen is 5/8" wide, and this weighs 3 1/4 oz
unboxed. Not signed as to the maker. This is in decent condition and
was cleaned. There are some overall scuffs from a previous cleaning.
The face has some light dings and some chips around the edge. The peen
is fairly good as is the eye. This ain't perfect, but drop it on a
handle and it will get the job done. $14.00
http://oldetoolshop.com/forsale/feb/hammer0203a.jpg
http://oldetoolshop.com/forsale/feb/hammer0203b.jpg
http://oldetoolshop.com/forsale/feb/hammer0203c.jpg
Vintage Sargent 6 Inch Side Cutter Pliers. Measuring 6 9/16" long and
this weighs 8 1/2 oz unboxed. This is in reasonably good condition and
was not cleaned. There is a little plating loss around the jaws, but
most of it is present. The jaws and the cross hatching are good. The
joint moves smoothly with no play. The handles are also good. This
ain't perfect, but it will get the job done. $17.00
http://oldetoolshop.com/forsale/feb/pliers0203a.jpg
http://oldetoolshop.com/forsale/feb/pliers0203b.jpg
http://oldetoolshop.com/forsale/feb/pliers0203c.jpg
http://oldetoolshop.com/forsale/feb/pliers0203d.jpg
http://oldetoolshop.com/forsale/feb/pliers0203e.jpg
Utica No 1050 8 Inch Linesman Pliers. Measuring 8 1/8" long and this
weighs 12 3/4 oz unboxed. This is in reasonably good condition and was
cleaned. There are few small spots of patina, but overall nothing too
bad. The jaws are good as is the cross hatching on the faces. The
cutter edges are also good with no dings or nicks. The joint is good
with no play. This ain't minty, but it is a quality tool that will get
the job done. $17.00
http://oldetoolshop.com/forsale/feb/pliers0204a.jpg
http://oldetoolshop.com/forsale/feb/pliers0204b.jpg
http://oldetoolshop.com/forsale/feb/pliers0204c.jpg
http://oldetoolshop.com/forsale/feb/pliers0204d.jpg
Hand Forged Blacksmith Straight Peen Head. Measuring 4 7/8" long, the
face is 1 1/4" square, the peen is 1 3/8" high, about 1/4" wide, and
this weighs 1 lb 12 1/2 oz unboxed. This has a mark, looks like 113,
but I can't say for sure, I'm thinking that this was a hot cut chisel
head originally, but the last guy or 3 were using this has a hammer.
This is in fair condition and was cleaned. There there is some overall
pitting and patina. The face has some dings, wear, and mushrooming.
The peen has some chipping on the sides and at the one end. The punched
eye also has some chipping on the one side and a little crusty on the
inside. This ain't pretty or perfect, but it will get the job done. $18.00
http://oldetoolshop.com/forsale/feb/blacksmith0201a.jpg
http://oldetoolshop.com/forsale/feb/blacksmith0201b.jpg
http://oldetoolshop.com/forsale/feb/blacksmith0201c.jpg
TWO Vintage E-Z Mark Door Butt Gauges. There is a 3 1/2", a 4", and
they weigh 12 1/2 oz unboxed. The one is marked Pat Pend, the other has
a patent number, but I can't find that anywhere. These are in decent
condition and were not cleaned. Both of them have some wear to the
finish and some light patina, but nothing too bad. All of the edges are
fairly good. These ain't minty, but they are a lot less common than the
Stanley ones, at least in my travels. $18.00
http://oldetoolshop.com/forsale/feb/markinggage0201a.jpg
http://oldetoolshop.com/forsale/feb/markinggage0201b.jpg
http://oldetoolshop.com/forsale/feb/markinggage0201c.jpg
http://oldetoolshop.com/forsale/feb/markinggage0201d.jpg
Greenlee No 900 24 Inch Brace Auger Bit Extension. Measuring 24" long
and this weighs 1 lb 4 3/4 oz unboxed. This is in reasonably good
condition and was cleaned. There are few light spots of patina on the
chuck area, but nothing too bad. The shaft has some staining and some
light pitting down by the shaft. The chuck works and was oiled (I put a
bit in it). This ain't minty, but it will allow you to stick yer bit
deeper than you ever could have imagined. Just saying. $19.00
http://oldetoolshop.com/forsale/feb/bracetool0202a.jpg
http://oldetoolshop.com/forsale/feb/bracetool0202b.jpg
Precision-Bilt 3/4 Inch Bevel Side Paring Chisel. Measuring 6 13/16"
from the edge to the end of the socket, the blade is 4 5/16" long, this
is 10 5/16" overall, and this weighs 5 1/4 oz unboxed. Precision-Bilt
was a brand name used by Spiegel Inc. on their line of wood working
tools. This is in reasonably good condition and was cleaned. The back
is good save for some light scuffs. There are some dings on the sides.
The edge will need some work. The top has some frosting and staining.
The socket does have some deep dings or what have you on the sides. The
handle looks to be original. That has some stains and wear to the end
leather washer, but it's solid. I did not have it off of the tool. This
ain't pristine, but I sure ain't seen too many of these guys around. $17.00
http://oldetoolshop.com/forsale/feb/chisel0202a.jpg
http://oldetoolshop.com/forsale/feb/chisel0202b.jpg
http://oldetoolshop.com/forsale/feb/chisel0202c.jpg
Millers Falls No 4 T-Auger Handle. Measuring 15 1/8" long and this
weighs 2 lbs 13 1/4 oz unboxed. This isn't signed, but few of these
were. This is in decent condition and was cleaned. The finish on the
chuck and head area is worn. The chuck and jaws are good and the
ratchet works in both directions and the locked position. The fixed
handle has a poorly done hanging hole. The spinning section on the
removable handle doesn't turn and was probably glued on at some point.
The handle does remove and works in both holes. This guy ain't pretty
or perfect, but it will get the job done. $45.00
http://oldetoolshop.com/forsale/feb/augerhandle0201a.jpg
http://oldetoolshop.com/forsale/feb/augerhandle0201b.jpg
http://oldetoolshop.com/forsale/feb/augerhandle0201c.jpg
http://oldetoolshop.com/forsale/feb/augerhandle0201d.jpg
http://oldetoolshop.com/forsale/feb/augerhandle0201e.jpg
Stillwell Patent 1956 C Washer Removing Pliers. Measuring 6 3/8" long
and this weighs 2 1/2 oz unboxed. Charles Stillwell was granted Pat.
No. 2,737,837 on Mar. 3, 1956 for the design of this tool. This is in
good condition and was cleaned. There are a few small spots of light
patina, but nothing too bad. The tips and joint are good. I gotta say,
that this is sure not a very common tool, at least in my travels. $16.00
http://oldetoolshop.com/forsale/feb/pliers0201a.jpg
http://oldetoolshop.com/forsale/feb/pliers0201b.jpg
http://oldetoolshop.com/forsale/feb/pliers0201c.jpg
http://oldetoolshop.com/forsale/feb/pliers0201d.jpg
Upson Nut Co No 69 1 Ft Folding Rule. This weighs 1/2 oz unboxed. The
Upson Nut Co. was a Unionville CT toolmaker in business from 1854 until
1911. This is in fair condition and was cleaned. The outer segments
have some staining and the inside ones also have some spots. The finish
is pretty much gone. The insides have some scratch marks from the
pins. The rulings are readable for the most part. The joints are good
and the side pin is present. This ain't minty, by any stretch, but
these smaller rules are sure getting few and far between. $14.00
http://oldetoolshop.com/forsale/feb/rule0201a.jpg
http://oldetoolshop.com/forsale/feb/rule0201b.jpg
http://oldetoolshop.com/forsale/feb/rule0201c.jpg
Heavy User Crafted Machinist Drill or V-Block & Clamp. Measuring 2
11/16" long, 1 15/16" wide, 2 7/16" high, and this weighs 3 lbs 1/4 oz
unboxed. Not signed as to the maker. This is in reasonably good
condition and was not cleaned. There is some overall staining, but
nothing too bad patina wise. The edges are cripsy good. The side
screws for the clamp work as does the top hold down screw. This ain't
got the fancy maker's mark, but it's a solid tool that will get the job
done. $19.00
http://oldetoolshop.com/forsale/feb/machinisttool0201a.jpg
http://oldetoolshop.com/forsale/feb/machinisttool0201b.jpg
http://oldetoolshop.com/forsale/feb/machinisttool0201c.jpg
http://oldetoolshop.com/forsale/feb/machinisttool0201d.jpg
--------------------------------------
"The right question is usually more important than the right answer."
Plato
Tony
Olde River Hard Goods
http://www.oldetoolshop.com
TSMusic on Facebook
http://www.facebook.com/tonyseomusic
|
