More than a few moons ago I would send them back and get them
re-handled. Don't know if they still provide this service.
It used to be the norm in many product lines.
You could not wear out a Zippo. My Dad sent his WWII era lighter back
several times. It always came back the original case filled with new guts.
Mike Graf
On 5/22/2015 3:12 AM, Thomas Conroy via OldTools wrote:
> bridger wrote:
> "... Instead I shifted the leather discs around to even up the spacing of them
on the handle and am figuring to soak them in something to get them to swell
back up to size. They seem to still be pretty pliable. I worked the surface of
the leather handle a bit with some coarse sandpaper to open it up. I'm wondering
what would be an appropriate material to soak them in. I can see not wanting
something that hardens and makes the leather brittle, but not something that
makes the leather soft and fragile either. A mix of mineral oil and linseed?
Maybe top that with shellac or something..."
>
> To the best of my knowledge and belief there is nothing you can do to
reinflate the shrunken leather of a leather washer handle. Nothing. No way.
Don't even bother to hope. Don't try to get anything into the leather, it will
be worse than useless. I've soaked old leather, of various kinds for for various
reasons, in neat's-foot oil. Soaked it in linseed oil. I've used neats-foot-
oil/lanolin leather dressings. If you are lucky soaking the washers will do
nothing much. If not lucky, you will get a disgusting, gummy, fragile mess. What
you **won't** do is improve the handle in any way whatever.
>
> Most likely your best bet is to push all the washers up really tight next to
each other. Then fill the gap between the last washer and the end, or maybe
leave the gap between the two last washers and fill that, by wrapping tightly
with thick thread or very thin cord. I might perhaps work glue down between the
washers before snugging them up, then lay in the filling cord in glue. When dry
put on a coat or two of shellac. The first coat of shellac will soak in a bit
but seal the surface, so you might need two or more. Or maybe glue ooze-out will
ahve sealed the surface. Smoothing or shaping the surface, or sanding to clean
it, probably won't do much good before the shellac is on, but will expose raw
leather and require a bit more shellac. Sanding leather, especially old leather,
usually doesn't work very well; trimming with a sharp edge tool is much more
successful. I would try a float, haven't yet but mean to.
>
> I could well be wrong in my opinion; I haven't attempted to restore a leather-
washer handle (though I have dealt with old washers on chisel handles, where
soaking in BLO with the rest of the handle sometimes is beneficial). If someone
has successfully tightened up an old leather-washer handle (without repeaning or
adding new solid material like the cord I suggest) I'll be happy to add it to my
list of possibilities. But at this point I've got about thirty years'
professional experience with old leather (mostly in the form of bookbindings)
and I wouldn't waste the energy hoping that its condition will be improved by
soaking it in something.
> Tom Conroy
>
> ------------------------------------------------------------------------
> OldTools is a mailing list catering to the interests of hand tool
> aficionados, both collectors and users, to discuss the history, usage,
> value, location, availability, collectibility, and restoration of
> traditional handtools, especially woodworking tools.
>
> To change your subscription options:
> http://old
tools.swingleydev.com/mailman/listinfo/oldtools
>
> To read the FAQ:
> http://swingleydev.com/archi
ve/faq.html
>
> OldTools archive: http://swingleydev.com/ot/">http://swingleydev.com/ot/
>
> OldTools@s...
> http://old
tools.swingleydev.com/mailman/listinfo/oldtools
>
|