The second run of goods for October. More fresh goodies both
collectible and usable.
PayPal is now accepted and preferred (if you use it) on all items. It's
easier for me to ship items off of a paid PayPal invoice, especially
First Class ones. Checks and money orders are still welcome.
And remember........da more ya buy, the cheaper they fly!
First contact (that is e-mail, or phone) that says I want it gets it.
Prices do not include shipping. All items are shipped with Delivery
Confirmation. Insurance, unless it is a big order or a very fragile item
is optional. Just let me know. Also, I am shipping a lot more stuff via
First Class mail. There will be a small amount added to the shipping
cover the cost of the padded mailer. I don't get them for free.
Please put your name and address in the message. Saves time and email
traffic!
---------------------------------------------------
Small Hand Forged Round Jaw Blacksmith Tongs. Measuring 6 15/16" long,
the jaws are 15/16" deep, 11/16" wide at the tips, and this weighs 6 1/2
oz unboxed. Not signed as to the maker, X did make his mark on the one
arm. This is in reasonably good condition and was cleaned. There is a
little patina but nothing worth kicking the cat over. The jaws are
good. The joint does have some wiggle. The handles are good other than
some light scuffing left over from when this was made. This is a neat
smaller tool that is ready to work. $19.00
http://oldetoolshop.com/forsale/oct/blacksmith1003a.jpg
http://oldetoolshop.com/forsale/oct/blacksmith1003b.jpg
http://oldetoolshop.com/forsale/oct/blacksmith1003c.jpg
Belgian Coticule Sharpening Stone. Measuring 5 15/16" long, 1 7/16"
wide, 13/16" thick, and this weighs 12 1/2 oz unboxed. Not signed as to
the maker. This is in good condition. The only cleaning was to take
some gunk and a few bits of paint off if it. The white face has is good
other than one tiny ding and some light chipping on the edges. It is
flat in both directions. The base has a few light scratches but that is
also good. This ain't pristine but it sure ain't bad and well go price
a new one. $50.00
http://oldetoolshop.com/forsale/oct/sharpeningstone1002a.jpg
http://oldetoolshop.com/forsale/oct/sharpeningstone1002b.jpg
http://oldetoolshop.com/forsale/oct/sharpeningstone1002c.jpg
Disston No 76 Marking Gage & H Disston & Sons Mortise Gage. They weigh 8
oz unboxed. These are in reasonably good condition and were cleaned.
The No. 76 marking gage has some staining but nothing too bad. The
point is good and the rulings are readable. The mortise gage has some
stains on the beam, which is not ruled. The head also has some stains
and a little wear on the face. The fixed point is good. The moveable
point is worn a little but there is enough to mark a mark. Both locking
screws work. These ain't minty but they are collectible tools that will
get the job done. $34.00
http://oldetoolshop.com/forsale/oct/mortisegage1002a.jpg
http://oldetoolshop.com/forsale/oct/mortisegage1002b.jpg
http://oldetoolshop.com/forsale/oct/mortisegage1002c.jpg
http://oldetoolshop.com/forsale/oct/mortisegage1002d.jpg
Carborundum Co No 131 Medium Sharpening Stone & Box. The stone is 5"
long, 1 1/2" wide, 1/2" high, this all weighs 6 1/2 oz unboxed. The
stone is in reasonably good condition, the only cleaning was with some
soap and water. The one face is flat across the long way, but there is
a whisker of wear in the center looking from the ends. The other face
is flat in all directions. The edges are good but there are a couple of
tiny chips on the corners. The box is in fair condition. There is some
staining and wear, and the one corner of the lid is ripped. This ain't
pristine but it is an old stone that will get the job done. $17.00
http://oldetoolshop.com/forsale/oct/sharpeningstone1001a.jpg
http://oldetoolshop.com/forsale/oct/sharpeningstone1001b.jpg
http://oldetoolshop.com/forsale/oct/sharpeningstone1001c.jpg
Fulton 3/4 Inch Bench Paring Chisel. Measuring 5 1/2" from the edge to
the end of the socket, the b lade is 3 3/8" long, this is 8 3/16"
overall, and this weighs 4 oz unboxed. This is in reasonably good
condition and was cleaned. The back has some light pitting down by the
socket but it's clean for the most part. The top is good other than
some staining. The socket has some dings but nothing too bad. The
handle is the original one. That has a little wear to the leather
washer on the end but otherwise it's ready to go. This ain't minty but
it will get the job done. $14.00
http://oldetoolshop.com/forsale/oct/chisel1006a.jpg
http://oldetoolshop.com/forsale/oct/chisel1006b.jpg
Brown & Sharpe Machinist Depth Gage. This weighs 1 1/4 oz unboxed.
This is in reasonably good condition and was cleaned. The head has some
light stained spots but the face is clean. The No. 11 tempered rule has
64ths on the front and 100ths on the back. That has some scratches and
stains but all the rulings are readable and the edges and corners are
good. The locking screw does it's job. This ain't pristine but it is a
quality tool that will get the job done. $16.00
http://oldetoolshop.com/forsale/oct/machinisttool1006a.jpg
http://oldetoolshop.com/forsale/oct/machinisttool1006b.jpg
http://oldetoolshop.com/forsale/oct/machinisttool1006c.jpg
Early Hand Forged Hammer Poll Adze Head. Measuring 9" long (straight
across), the edge is 3 3/8" wide, and this weighs 3 lbs 7 oz unboxed.
The mark is hard to read, but it looks like Maw (Sheffield 1821). There
is a Crown stamp as well. This is in decent condition and was cleaned.
This has a wrought iron body with a steel face and edge. There is some
overall pitting and patina. The b lade has some pitting but there is
lots of steel left. The hammer poll is good save for some light
pitting. The eye has some crusty inside, some dinging at the top and
there is a small check at the one corner. This is far from perfect but
200 year old tools rarely are. $45.00
http://oldetoolshop.com/forsale/oct/earlyadze1001a.jpg
http://oldetoolshop.com/forsale/oct/earlyadze1001b.jpg
http://oldetoolshop.com/forsale/oct/earlyadze1001c.jpg
http://oldetoolshop.com/forsale/oct/earlyadze1001d.jpg
Billings 12 oz Ball Peen Hammer. Measuring 13" overall, the head is 3
1/16" long, the face is 7/8" in diameter, the peen is 11/16" in
diameter, and this weighs 11 3/4 oz unboxed. This is in reasonably good
condition and was cleaned. The head has some dings on the sides and a
little staining but nothing too bad. The face is good save for some
light dings. The peen is also good. The handle looks to be the original
one. That has some stains but it's solid. This ain't pristine but it
is a quality tool that will get the job done. $18.00
http://oldetoolshop.com/forsale/oct/hammer1004a.jpg
http://oldetoolshop.com/forsale/oct/hammer1004b.jpg
http://oldetoolshop.com/forsale/oct/hammer1004c.jpg
Small Hand Forged Stone Mason Hammer. Measuring 11 3/4" overall, the
head is 4 7/16" long, the face is 11/16" high, 3/4" wide, the peen is 1
1/16" wide, and this weighs 12 1/2 oz unboxed. Not signed as to the
maker. This is in decent condition and was cleaned. The head has some
light patina and some scuffs left over from when this was made. The
steel face has some dings, wear, and a little mushrooming on the edges.
There are a couple of small voids along the forge weld line with the
body. The peen is good other than some light roughness. The handle is
old. That is good save for some light rasp marks at the end. This
ain't fancy but it is a neat older tool that does not show up in this
size very often. $17.00
http://oldetoolshop.com/forsale/oct/hammer1005a.jpg
http://oldetoolshop.com/forsale/oct/hammer1005b.jpg
http://oldetoolshop.com/forsale/oct/hammer1005c.jpg
Eifel 8 1/2 Inch Plierench With 3 Jaws. Measuring 8 5/8" long and this
all weighs 1 lb 4 oz unboxed. This is in reasonably good condition and
was cleaned. There is a little patina on the head but nothing too bad.
The one jaw has some chipping on the teeth, the other two are good. The
action works and the jaws do remove. The handles are also good. This
ain't pristine but finding one with extra jaws sure ain't getting any
easier to do. $28.00
http://oldetoolshop.com/forsale/oct/wrench1001a.jpg
http://oldetoolshop.com/forsale/oct/wrench1001b.jpg
http://oldetoolshop.com/forsale/oct/wrench1001c.jpg
http://oldetoolshop.com/forsale/oct/wrench1001d.jpg
Hand Forged Early Alligator Wrench. Measuring 8 3/8" long, 11/16"
across the opening on the jaws, and this weighs 9 oz unboxed. There is
a name stamped on the side, might be the maker or a user. This is in
decent condition and was cleaned. There is some overall patina, but I
doubt that this guy was real pretty to start with. The jaws and teeth
are good. The end of the handle has some pitting, this might have been
fitted to a wooden handle at some point. This ain't fancy but it is a
well made older tool. $17.00
http://oldetoolshop.com/forsale/oct/hfwrench1001a.jpg
http://oldetoolshop.com/forsale/oct/hfwrench1001b.jpg
http://oldetoolshop.com/forsale/oct/hfwrench1001c.jpg
Perfect Handle Style Screwdriver For Split Nut Saws. Measuring 7 7/8"
long, 5/16" across the outside of the tips, 3/16" across the inside, and
this weighs 4 oz unboxed. Not signed as to the maker, there is a faint
Germany mark. Looks to be user modified. This is in decent condition
and was cleaned. There is some overall light pitting on the shaft and
frame. The tips are good. The handle scales have some staining and the
one is warped outward a little at the top. This ain't fancy and it sure
ain't pretty but it is neat and working old tool. $18.00
http://oldetoolshop.com/forsale/oct/phsd1002a.jpg
http://oldetoolshop.com/forsale/oct/phsd1002b.jpg
Keuffel & Esser No 6481 12 oz Brass Plumb Bob. Measuring 4 15/16" long,
1 5/16" in diameter, and this weighs 11 3/4 oz unboxed. This is in
decent condition and was cleaned by someone else. There are some dings
and wear on the body. The steel tip is good but does not remove. The
string cap comes off and the holes are clear. The top of the cap is
scuffed a bit. This ain't minty but it will get the job done. $16.00
http://oldetoolshop.com/forsale/oct/plumbbob1001a.jpg
http://oldetoolshop.com/forsale/oct/plumbbob1001b.jpg
Wm Horn & Bro Philadelphia Cobblers Boot Peg Float. Measuring 20 1/4"
overall (straight across), the head is 2 7/8" long, 1" wide, and this
weighs 11 1/4 oz unboxed. William H Horn & Bro made cobblers and other
tools in Philadelphia PA from 1890 until 1902. This is in reasonably
good condition and was cleaned. There is a little frosting on the top
of the head. The trimming edge could stand a touch up. The float teeth
have some light patina. The teeth feel good but could also stand a
quick once over. The shaft is good. The handle is the original one.
That has some stains but there is some nice figure to the wood. There
is small check under the ferrule but it's on tight. This ain't perfect
but considering the age of the tool, well it sure ain't bad. $28.00
http://oldetoolshop.com/forsale/oct/leathertool1001a.jpg
http://oldetoolshop.com/forsale/oct/leathertool1001b.jpg
http://oldetoolshop.com/forsale/oct/leathertool1001c.jpg
Small Machinist Tool Maker Surface Gage. The base is 2 3/16" long, 1
9/16" wide, The post is 4 7/16" long, and this weighs 10 1/2 oz
unboxed. Not signed as to the maker. This is in reasonably good
condition and was cleaned by someone else. The top and sides of the
base have some spots of light pitting and frosting and there is a
prominent user name on the top. The underside is good other than some
light scratches. The leveling pins work. The post and pointer are
good. The locking, pointer, and fine adjuster all work. This ain't
minty but it will get the job done. $25.00
http://oldetoolshop.com/forsale/oct/machinisttool1005a.jpg
http://oldetoolshop.com/forsale/oct/machinisttool1005b.jpg
http://oldetoolshop.com/forsale/oct/machinisttool1005c.jpg
http://oldetoolshop.com/forsale/oct/machinisttool1005d.jpg
Hand Forged Early Bench Dog. Measuring 4 3/4" long. 1 13/16" across the
tips, 1 3/16" high at the front, 1 7/16" at the end, and this weighs 5
oz unboxed. Not signed as to the maker. This is in decent condition
and was cleaned. There is the usual patina. The front tips are good.
The back one which gets hammered into the bench top is broken off a
little. This ain't minty but these guys are sure few and far between of
late. $22.00
http://oldetoolshop.com/forsale/oct/hfbenchdog1001a.jpg
http://oldetoolshop.com/forsale/oct/hfbenchdog1001b.jpg
http://oldetoolshop.com/forsale/oct/hfbenchdog1001c.jpg
Greenlee 5/16 Inch Bench Gouge. Measuring 8 1/2" from the edge to the
end of the socket, the b lade is 6 3/4" long, 5/16" across the outside,
this is 13" overall, and this weighs 3 3/4 oz unboxed. This is in decent
condition and was cleaned. The back of the sweep is good other than
some very light frosting. The inside has some light patina. The socket
has some light pitting. The handle looks to be the original one. That
has some stains and a little roughness on the end but it's solid. This
ain't pristine but it will get the job done. $17.00
http://oldetoolshop.com/forsale/oct/chisel1003a.jpg
http://oldetoolshop.com/forsale/oct/chisel1003b.jpg
Vintage 6 Inch Wing Divider Or Compass. Measuring 6 1/4" long and this
weighs 4 1/4 oz unboxed. Not signed as to the maker, this is just
marked Made In USA. This is in reasonably good condition and was
cleaned. There is a little frosting but nothing too bad. The joint and
tips are good. The locking screw and fine adjuster nut both work. This
ain't minty but it's a solid tool that will get the job done. $18.00
http://oldetoolshop.com/forsale/oct/divider1002a.jpg
http://oldetoolshop.com/forsale/oct/divider1002b.jpg
http://oldetoolshop.com/forsale/oct/divider1002c.jpg
Machinist Tools
L S Starrett No 603 Machinist 6 Inch Rule. This weighs 1 oz unboxed.
This is in reasonably good condition and was not cleaned, at least by
me. There are some staining and lightly frosted spots mainly on the
back. All the rulings are readable and the edges and corners are good.
This ain't perfect but it will get the job done. $16.00
http://oldetoolshop.com/forsale/oct/machinisttool1003a.jpg
http://oldetoolshop.com/forsale/oct/machinisttool1003b.jpg
http://oldetoolshop.com/forsale/oct/machinisttool1003c.jpg
TWO Machinist V-Blocks & Clamp. The blocks are 2" long, 1 1/2" square,
and this all weighs 1 lb 15 3/4 oz unboxed. Not signed as to the
maker. These are in reasonably good condition and were cleaned. The
blocks have some frosting and a little staining but nothing too bad.
The grooves and edges are all good. The clamp is one that I had here
but it fits. That is also good and the screw travels the full
distance. These ain't minty but they will get the job done. $28.00
http://oldetoolshop.com/forsale/sept/machinisttool0912a.jpg
http://oldetoolshop.com/forsale/sept/machinisttool0912b.jpg
http://oldetoolshop.com/forsale/sept/machinisttool0912c.jpg
http://oldetoolshop.com/forsale/sept/machinisttool0912d.jpg
L S Starrett No 75 Fay Pattern 5 Inch Outside Caliper. Measuring 5 3/4"
long and this weighs 2 1/2 oz unboxed. This is in reasonably good
condition and was cleaned. There is a little frosting on the legs but
nothing too bad. The spring and tips are good. The threads have a few
light dings but the nut travels the full distance smoothly. I did put
some oil on them. This ain't perfect but it is a quality tool that will
get the job done. $18.00
http://oldetoolshop.com/forsale/sept/machinisttool0914a.jpg
http://oldetoolshop.com/forsale/sept/machinisttool0914b.jpg
http://oldetoolshop.com/forsale/sept/machinisttool0914c.jpg
L S Starrett No 83 A 8 Inch Machinist Divider & Box. This weighs 8 oz
unboxed. This is in reasonably good condition and was cleaned. There
is a little frosting and staining on the legs but nothing too bad. The
joint is good and the nut travels the full distance smoothly. The one
tip had a small piece added to it at some point. The box lid has some
wear and two of the corners are ripped. This ain't minty and it sure
ain't got that kind of price tag but it will get the job done. $22.00
http://oldetoolshop.com/forsale/sept/machinisttool0908a.jpg
http://oldetoolshop.com/forsale/sept/machinisttool0908b.jpg
http://oldetoolshop.com/forsale/sept/machinisttool0908c.jpg
http://oldetoolshop.com/forsale/sept/machinisttool0908d.jpg
Two L S Starrett No 870 Small Hole Gages, There is the A and the C size
and they weigh 3/4 oz unboxed. The model number on the C is faint.
These are in good condition and were not cleaned. There really ain't
much patina at all on these guys. The tips are good and the screws
work. These are handy tools and priced well below what new ones are
selling for. $28.00
http://oldetoolshop.com/forsale/april/machinisttool0418a.jpg
http://oldetoolshop.com/forsale/april/machinisttool0418b.jpg
http://oldetoolshop.com/forsale/april/machinisttool0418c.jpg
L S Starrett No 391 Machinist Center Gage. This weighs 1/2 oz unboxed.
This is in decent condition and was cleaned by someone else. There is
some frosting and a few dots of patina. There is a user mark on the
back. The edges are good and all the markings are readable. This ain't
pristine but it will get the job done. $14.00
http://oldetoolshop.com/forsale/april/machinisttool0401a.jpg
http://oldetoolshop.com/forsale/april/machinisttool0401b.jpg
Woodworking Tools
Vintage Small Wood Handle Turnscrew Or Screwdriver. Measuring 5 5/16"
long, the tip is 1/4" wide, and this weighs 3/4 oz unboxed. Not signed
as to the maker. This is in reasonably good condition and was cleaned.
The b lade has some staining but nothing too bad patina wise. The tip
has a little wear. The handle is good other than a little staining.
This ain't pristine but it's pretty darn close. $18.00
http://oldetoolshop.com/forsale/oct/turnscrew1002a.jpg
http://oldetoolshop.com/forsale/oct/turnscrew1002b.jpg
Lufkin No 171 (36) 6 Inch Carpenters Caliper Rule. This weighs 1 oz
unboxed. This is in reasonably good condition and was cleaned. There is
a little wear to the wood and the inking but the rulings are all
readable. The joint is good and the side pin is present. The caliper is
a little loose but that can be fixed with some paste wax. This ain't
minty but these small ones rarely are. $19.00
http://oldetoolshop.com/forsale/oct/rule1001a.jpg
http://oldetoolshop.com/forsale/oct/rule1001b.jpg
Rosewood & Brass Marking & Mortising Gage. Measuring 7 7/8" long and
this weighs 6 1/4 oz unboxed. Not signed as to the maker. This is in
good condition. The only cleaning was a coat of wax. There are a few
light dings on the beam and head but nothing too bad. All three points
are good. The slider moves and the locking screw works. This ain't the
fanciest but it is a good looking tool that will get the job done. $24.00
http://oldetoolshop.com/forsale/oct/mortisegage1001a.jpg
http://oldetoolshop.com/forsale/oct/mortisegage1001b.jpg
http://oldetoolshop.com/forsale/oct/mortisegage1001c.jpg
http://oldetoolshop.com/forsale/oct/mortisegage1001d.jpg
Vintage 3 Inch Pocket Level. Measuring 3" long and this weighs 2 1/2 oz
unboxed. Not signed as to the maker. This is in reasonably good
condition and was cleaned. The brass plate has a few stains and moves
around a little. The pins do remove. The finish is original and about
90% present. The locking screw works and was oiled. This ain't fancy
but it will get the job done. $15.00
http://oldetoolshop.com/forsale/oct/level1001a.jpg
http://oldetoolshop.com/forsale/oct/level1001b.jpg
Small Vintage Perfect Handle Style Screwdriver. Measuring 4 11/16"
long, the tip is 1/8" wide, and this weighs 1 1/4 oz unboxed. Not
signed as to the maker. This is in decent condition and was cleaned.
There is some frosting and a few spots of light pitting on the tip and
shaft. The sides of the tip were dressed down at some point. The
handle scales have some stains but are solid. There is a whisker of
mushrooming on the end of the handle. This ain't pristine but it will
get the job done. $15.00
http://oldetoolshop.com/forsale/oct/phsd1001a.jpg
http://oldetoolshop.com/forsale/oct/phsd1001b.jpg
P S & W No 1 Ex 7 Inch Draw Knife. Measuring 12 7/8" overall, the b
lade is 6 5/8" long, 1 3/8" wide at the ends, 1 5/16" at the center, and
this weighs 14 3/4 oz unboxed. This is in decent condition and was
cleaned. The steel area of the back has some frosting and some tiny
dots but nothing too bad. The iron frame has some spots of putting.
The top has some dings and I did take some some mushrooming on the top
of the back. That ain't perfect but it's better than it was. The top
of the front also has some dinging and light mushrooming. The rest of
the front has some overall light pitting. The handles are black
walnut. They have some dings and stains. The left one wiggles a hair.
The ferrules have some frosting and a few spots of pitting, the end caps
just some frosting. This ain't minty but it is quality tool in a hard
to find smaller size and it will get the job done. $38.00
http://oldetoolshop.com/forsale/oct/drawknife1001a.jpg
http://oldetoolshop.com/forsale/oct/drawknife1001b.jpg
http://oldetoolshop.com/forsale/oct/drawknife1001c.jpg
H Chapin Union Factory 1 Inch Brass Sole Straight Rabbet Plane To
RESTORE. Measuring 9 1/2" long, 15/16" wide across the sole, and this
weighs 1 lb 1/2 oz unboxed. This is in to restore condition and was
lightly cleaned. The body has some light scratches and there are some
bits of paint down in the grain. The brass sole was probably user added
but that is good and it is straight. The wedge has a crack on the one
side. That could be glued or at least used as a pattern for a new one.
This will need an iron. This is what it is but it is a neat plane that
with some work, will get the job done. $18.00
http://oldetoolshop.com/forsale/oct/woodenplane1001a.jpg
http://oldetoolshop.com/forsale/oct/woodenplane1001b.jpg
http://oldetoolshop.com/forsale/oct/woodenplane1001c.jpg
http://oldetoolshop.com/forsale/oct/woodenplane1001d.jpg
North Bros Yankee 1/4 Inch Screwdriver. Measuring 7 7/16" long, the tip
is 1/4" wide, and this weighs 2 1/2 oz unboxed. North Bros Div of
Stanley. This is in reasonably good condition and was cleaned. The tip
and shaft are good. The ferrule has a little patina. The handle finish
has a little wear but most of it is present. This ain't perfect but as
these guys go, well it sure ain't bad. $14.00
http://oldetoolshop.com/forsale/sept/screwdriver0901a.jpg
http://oldetoolshop.com/forsale/sept/screwdriver0901b.jpg
Stanley No 424 Aluminum Carpenters Zig Zag Rule. This weighs 4 oz
unboxed. There are 3 patent dates on the end but nothing for any of
them shows up on the old radar. This is in decent condition and was not
cleaned. This does have most of the original black finish. The sides
have some light funky. The joints have some rust on the insides but
they all work and lock. This sure ain't minty but for the age it ain't
all that bad. $14.00
http://oldetoolshop.com/forsale/sept/rule0903a.jpg
http://oldetoolshop.com/forsale/sept/rule0903b.jpg
http://oldetoolshop.com/forsale/sept/rule0903c.jpg
Stanley SW No 25 10 Inch Adjustable Bevel Square. This weighs 5 1/4 oz
unboxed. This is in fair but working condition and was cleaned. The b
lade has some spots of pitting but the edges are fairly good. The handle
has some wear to the edges and some dings but it still has a remnant of
the decal. The locking screw works. This ain't pretty or perfect but
it will get the job done. $15.00
http://oldetoolshop.com/forsale/sept/square0901a.jpg
http://oldetoolshop.com/forsale/sept/square0901b.jpg
Chapin-Stephens No 61 2 Ft Folding Carpenters Rule. This weighs 1 1/2
oz unboxed. This is in reasonably good condition and was not cleaned.
The finish on the boxwood has a little wear and a few lightly stained
spots. All the rulings are readable and the joints are good. The one
inside pin is bent, the other one and the side pin is good. The brass
has a little patina. This ain't minty but it sure ain't bad as these
guys go. $20.00
http://oldetoolshop.com/forsale/sept/rule0902a.jpg
http://oldetoolshop.com/forsale/sept/rule0902b.jpg
Vintage Iron Spokeshave Or Spoke Shave. Measuring 9 1/4" overall, the b
lade is 2" wide, and this weighs 10 3/4 oz unboxed. Not signed as to
the maker, this style was made by several makers. This is in decent
condition and was cleaned. The finish is original and about 75%. There
is a little funky on there including some tiny bits of paint. The cap
and screw are good. The sole has some scratches and frosting. The b
lade has some staining and a little frosting. That will need a touch
up. This ain't perfect but it will get the job done. $17.00
http://oldetoolshop.com/forsale/sept/spokeshave0901a.jpg
http://oldetoolshop.com/forsale/sept/spokeshave0901b.jpg
http://oldetoolshop.com/forsale/sept/spokeshave0901c.jpg
P S & W No 1 EX 12 Inch Draw Knife Or Drawknife. Measuring 18 3/4"
overall, the b lade is 11 7/8" long, 1 3/8" wide at the center, 1 3/8"
at the ends, and this weighs 1 lb 3 1/2 oz unboxed. This is in decent
condition and was cleaned. The steel area of the back has some frosting
and a few small spots of light pitting but nothing too bad. The edge
has some tiny dings. The top is good and was never struck. The front
has some patina including a few scratches. The handles are black
walnut. The right one has some dings and wear, the left one has some
thin checks and wiggles a little. The ferrules and end caps have some
frosting. This ain't minty but it will get the job done. $32.00
http://oldetoolshop.com/forsale/sept/drawknife0901a.jpg
http://oldetoolshop.com/forsale/sept/drawknife0901b.jpg
http://oldetoolshop.com/forsale/sept/drawknife0901c.jpg
Other Trades & Collectibles
C Drew Boat Builders Caulking Iron. Measuring 5 15/16" long, 1 7/8"
across the edge, and this weighs 6 oz unboxed. Also marked Cast Steel
on the back. This is in fair condition and was cleaned. There is some
overall pitting. The edge was chipped and I dressed it a bit and there
still are chips on the ends. That will need some more work. The
striking button also has a small chip off of the rim. This ain't pretty
or perfect but with a little work it will get the job done. $14.00
http://oldetoolshop.com/forsale/sept/caulkingiron0901a.jpg
http://oldetoolshop.com/forsale/sept/caulkingiron0901b.jpg
http://oldetoolshop.com/forsale/sept/caulkingiron0901c.jpg
Early Hand Forged 1 1/4 lb Cross Peen Hammer Head. Measuring 5" long,
the face is 1 1/16" square, the peen is 1 1/2" wide, and this weighs 1
lb 6 1/2 oz unboxed. Not signed as to the maker. This is in decent
condition and was cleaned. This has a steel face and peen on an iron
body. There is some overall light patina. The face has some dings and
light cut marks. The sides of the face were dressed at some point but
there is a little bit of mushrooming. The peen has some light dings and
there is a bit of a void starting on the top at the forge weld line.
The punched eye is good. This ain't minty but it is an early tool that
will get the job done. $18.00
http://oldetoolshop.com/forsale/sept/hammer0915a.jpg
http://oldetoolshop.com/forsale/sept/hammer0915b.jpg
http://oldetoolshop.com/forsale/sept/hammer0915c.jpg
Hand Forged Blacksmith 1 1/2 lb Straight Peen Hammer Head, Measuring 4
9/16" long, the face is 1 1/4" in diameter, the peen is 1 1/4" high, and
this weighs 1 lb 9 oz unboxed. Not signed as to the maker. This is in
decent condition and was cleaned. There is some overall light pitting
on the body. The face has some dings and there is some chipping around
the edge. The peen is fairly good. The punched eye, well let's just say
whoever made this wasn't having a great day in that department, but it's
good with no cracks. This ain't the prettiest but it will get the job
done. $18.00
http://oldetoolshop.com/forsale/sept/hammer0916a.jpg
http://oldetoolshop.com/forsale/sept/hammer0916b.jpg
http://oldetoolshop.com/forsale/sept/hammer0916c.jpg
Vintage Slater Slate Ripper Roof Removal Tool. Measuring 29" long and
this weighs 2 lbs 7 1/2 oz unboxed. Not signed as to the maker. This
is in reasonably good condition and was cleaned by someone else. There
is some pitting on the top and some deeper stuff by the handle on the
underside. The head is good with no cracks. The front of the handle
which is usually banged up is also good. This ain't minty but it is a
well made tool that will get the job done. $28.00
http://oldetoolshop.com/forsale/sept/slatetool0903a.jpg
http://oldetoolshop.com/forsale/sept/slatetool0903b.jpg
http://oldetoolshop.com/forsale/sept/slatetool0903c.jpg
http://oldetoolshop.com/forsale/sept/slatetool0903d.jpg
Original .560 Inch Round Ball Black Powder Bullet Mold. Measuring 5
9/16" long, the cavities are .560 inch in diameter, and this weighs 2
1/2 oz unboxed. Not signed as to the maker. This is in decent
condition and was cleaned. There is some overall pitting on the head
and arms. The cavities have some light rust inside. There is a whisker
of daylight showing when they are closed. The joint has a little
wiggle. This ain't minty but is is a hard to find size. $27.00
http://oldetoolshop.com/forsale/sept/guntool0907a.jpg
http://oldetoolshop.com/forsale/sept/guntool0907b.jpg
http://oldetoolshop.com/forsale/sept/guntool0907c.jpg
Neat Small 3 Inch Adjustable Wrench, Measuring 3 1/16 long and this
weighs 1 oz unboxed. Not signed as to the maker. This is in reasonably
good condition and was not cleaned. There is a little rust on the one
side and the back edge. The jaws are good. This ain't fancy but it
sure is neat. $14.00
http://oldetoolshop.com/forsale/sept/wrench0903a.jpg
http://oldetoolshop.com/forsale/sept/wrench0903b.jpg
Lufkin Surveyor Survey Tape Puller. Measuring 2 7/8" wide, 2 1/4" high,
and this weighs 4 1/2 oz unboxed. This is in reasonably good condition
and was not cleaned. There are some light scuffs, a little staining,
and one small spot of rust but this almost all of the original plating.
The gripping area is good to go. I gotta say, that this is not a very
common tool, at least in my travels. $25.00
http://oldetoolshop.com/forsale/sept/machinisttool0905a.jpg
http://oldetoolshop.com/forsale/sept/machinisttool0905b.jpg
http://oldetoolshop.com/forsale/sept/machinisttool0905c.jpg
Hand Forged Saw Makers Setting Hammer Head. Measuring 6 1/4" long, the
faces are 1 1/8" and 1 3/16" wide, and this weighs 1 lb 5 3/4 oz
unboxed. Not signed as to the maker. Not signed as to the maker. This
is in decent condition and was cleaned. There is some overall pitting.
The faces are fairly good and were dressed at some point. The punched
eye has a little paint inside (this guy was covered with it when it got
here) but it's good to go. This ain't perfect but this is one of those
hard to find hammers. $18.00
http://oldetoolshop.com/forsale/sept/hammer0911a.jpg
http://oldetoolshop.com/forsale/sept/hammer0911b.jpg
http://oldetoolshop.com/forsale/sept/hammer0911c.jpg
Original .460 Round Ball Black Powder Mold. Measuring 5 9/16" long, the
cavity is .460 inch in diameter, and this weighs 4 3/4 oz unboxed. Not
signed as to the maker. This is in decent condition and was cleaned.
There is some overall pitting on the head and arms. The cavities have
some tiny dings on the side edges that would need to be dressed, but the
head closes tight with almost no daylight showing. The joint has a
little wiggle and the sprue trimmers will need a touch up. This ain't
minty but it is a hard to find size in one of these guys. $24.00
http://oldetoolshop.com/forsale/sept/guntool0906a.jpg
http://oldetoolshop.com/forsale/sept/guntool0906b.jpg
http://oldetoolshop.com/forsale/sept/guntool0906c.jpg
Original Double Cavity 30 Cal Pistol Bullet Mold. Measuring 4 5/16"
long, the cavities are .282 inches across, and this weighs 4 oz
unboxed. Not signed as to the maker. This is in decent condition and
was cleaned. There is some overall pitting. The cavities are good
other than a little rust staining. There is a little daylight showing
when they are closed. The joint is good with no play. The handles are
bent a little. This ain't pristine but considering the age of this guy,
it ain't all that bad. $40.00
http://oldetoolshop.com/forsale/sept/guntool0903a.jpg
http://oldetoolshop.com/forsale/sept/guntool0903b.jpg
http://oldetoolshop.com/forsale/sept/guntool0903c.jpg
Blacksmith Forged 3/4 lb Cross Peen Hammer Head. Measuring 3 5/8" long,
the face is 15/16" wide, 7/8" high, the peen is 1 1/8" wide, and this
weighs 13 3/4 oz unboxed. Not signed as to the maker. This is in decent
condition and was cleaned. There is some overall pitting and patina on
the head. The face has some light dings, scratches, and there is a
small chip on the one side. The peen is good. The punched eye is also
good save for a little crusty on the inside. This ain't minty but it is
a good size for a kid's hammer. $17.00
http://oldetoolshop.com/forsale/sept/hammer0906a.jpg
http://oldetoolshop.com/forsale/sept/hammer0906b.jpg
http://oldetoolshop.com/forsale/sept/hammer0906c.jpg
Hand Forged Early Blacksmith Tongs. Measuring 19 3/8" long, the jaws
are 1 11/16" deep, 13/16" wide at the tips, and this weighs 2 lbs 5 3/4
oz unboxed. Not signed as to the maker. This is in decent condition.
One of my flea market hero's hit this good with the shiny stuff. There
is the usual patina. The one jaw is a little thinner than the other one
and has a little chipping on the end. The rivet is a bit banged up and
the joint has some wiggle. These ain't pretty but they sure are shiny
and they will get the job done. $22.00
http://oldetoolshop.com/forsale/sept/blacksmith0901a.jpg
http://oldetoolshop.com/forsale/sept/blacksmith0901b.jpg
http://oldetoolshop.com/forsale/sept/blacksmith0901c.jpg
Early Hand Forged Oyster Or Clam Shucking Knife. Measuring 7 7/8"
overall, the tip is 3/8" at the widest spot, the handle is tapered, 7/8"
wide at the top, 15/16" wide at the end, 9/16" thick at the end, and
this weighs 13 1/2 oz unboxed. Not signed as to the maker. This is in
decent condition and was cleaned. There is some overall light patina.
The tip is good other than a slight bend looking from the side. The
handle is also good save for a small chip off of the end. This ain't
pretty but it wasn't made to do a pretty job either. $24.00
http://oldetoolshop.com/forsale/sept/hfclamknife0901a.jpg
http://oldetoolshop.com/forsale/sept/hfclamknife0901b.jpg
Stanley SW 3/4 lb Ball Peen Hammer Head. Measuring 3 9/16" long, the
face is 1 1/8" in diameter, the peen is 15/16" in diameter, and this
weighs 12 3/4 oz unboxed. The mark is faint but can be read. This is in
decent condition and was cleaned. There is some overall patina. The
face has some dings, wear, and I did run a file over some sharp
mushrooming around the edge. The peen is good save for some light
dings. The eye is good other than a little dinging on the inside. This
ain't minty, but these guys sure do not show up every day. $17.00
http://oldetoolshop.com/forsale/sept/hammer0903a.jpg
http://oldetoolshop.com/forsale/sept/hammer0903b.jpg
http://oldetoolshop.com/forsale/sept/hammer0903c.jpg
Hand Forged Flat Jaw Blacksmith Tongs. Measuring 19 1/4" long, the jaws
are 1 5/8" deep, 7/8" and 1" wide at the tips, they close to 3/8", and
this weighs 2 lbs 5 1/2 oz unboxed. Not signed as to the maker. This is
in decent condition. One of my flea market hero's hit this good with the
shiny stuff. There is the usual patina. The jaws have some dings but are
good. The joint has some crusty down inside but that is also good with
no play. $22.00
http://oldetoolshop.com/forsale/aug/blacksmith0801a.jpg
http://oldetoolshop.com/forsale/aug/blacksmith0801b.jpg
http://oldetoolshop.com/forsale/aug/blacksmith0801c.jpg
TWO W Schollhorn 6 Inch Tools. There is a divider measuring 6" long, an
outside caliper measuring 6" long, and they weigh 6 1/4 oz unboxed.
Frank P. Pfleghar and William Schollhorn of New Haven, CT were granted
Pat. No. 51,967 on Jan. 9, 1866 for the design of these tools. These
are in reasonably good condition and were cleaned. There is a little
frosting and a few small spots of pitting on both. The joints are both
good and the locking screws are correct and work. The tips on the
divider have the steel points and the tips of the outside caliper are
good. These ain't minty but they sure ain't bad. $55.00
http://oldetoolshop.com/forsale/july/divider0703a.jpg
http://oldetoolshop.com/forsale/july/divider0703b.jpg
http://oldetoolshop.com/forsale/july/divider0703c.jpg
-----------------------------------------------
"All men make mistakes, but married men find out about them sooner."
Red Skelton
Tony
Olde River Hard Goods
http://www.oldetoolshop.com
TSMusic on Facebook
http://www.facebook.com/tonyseomusic
|