OldTools Archive

Summer is in full bloom.  There are a bunch of fresh goodies on the list 
and some good stuff in the NOS section.  There ain't an infinite supply 
of these items so don't wait.

PayPal is now accepted and preferred (if you use it) on all items.   On 
items less than $25 (not including shipping) I would appreciate you 
using the Send Money to Family & Friends option so I don't get killed 
with the fees but that is your call. Checks and money orders are still 
welcome, it just seems that 1st Class letters seem to be taking forever 
to get from there to here.

And remember........da more ya buy, the cheaper they fly!

First contact (that is e-mail, or phone)  that says I want it gets it. 
Oldtools terms, except on items and orders over $100, if I don't know ya 
or haven't done business in the past (and my records good way back..) 
then it's pre-pay.  I do take PayPal (except as noted).  Prices do not 
include shipping.  All items are shipped with Delivery Confirmation. 
Insurance, unless it is a big order or a very fragile item is optional. 
Just let me know.  Also, I  am shipping a lot more stuff via First Class 
mail.  There will be a small amount added to the shipping cover the cost 
of the padded mailer.  I don't get them for free.

Please put your name and address in the message.  Saves time and email 
traffic!
---------------------------------------------------

Tyzack Turner No 660 Talisman 24 Inch 7 PT Cross Cut Saw NOS Quality Tool

Tyzack Turner No 660 Talisman 24 Inch 7 PT Cross Cut Saw.  This weighs 1 
lb 9 oz unboxed.  This is NOS, that's New Old Stock, and was not 
cleaned.  There ain't nothing at all to fuss about with this guy.  The 
blade is shiny and sharp.  There is a little bit of the protective 
coating showing at the toe.  The tote and saw nuts are as good as they 
get.  This is a quality tool made by an well respected English saw maker 
and I have been selling and shipping saws now for over 24 years so I 
know what I'm talking about.  $45.00

http://oldetoolshop.com/forsale/july/saw0701a.jpg
http://oldetoolshop.com/forsale/july/saw0701b.jpg
http://oldetoolshop.com/forsale/july/saw0701c.jpg
http://oldetoolshop.com/forsale/july/saw0701d.jpg
http://oldetoolshop.com/forsale/july/saw0701e.jpg

Tyzack Turner No 166 Talisman 10 Inch 13 PT Tenon Saw.  This weighs 1 lb 
3 1/2 oz unboxed. This is NOS, that's New Old Stock, and was not 
cleaned. There are some spots of funky on the brass back from being 
stored but the blade is factory bright.  The handle finish is perfect. 
There also is a little funky on the one sawnut on the front and some on 
the nuts on the back, (these weren't stored in a very nice place.) 
Nothing worth kicking the cat over.  If you are looking for a top 
quality back saw, you can't do much better than this for the price.  $60.00

http://oldetoolshop.com/forsale/june/saw0606a.jpg
http://oldetoolshop.com/forsale/june/saw0606b.jpg
http://oldetoolshop.com/forsale/june/saw0606c.jpg
http://oldetoolshop.com/forsale/june/saw0606d.jpg

NOS Tyzack Sons & Turner No 130 8 Inch Gentleman's Brass Back Dovetail 
Saw.  Measuring 12 13/16" overall, the blade is 8" long, 1 9/16" high 
(from the teeth to the start of the back), this is sharpened to 15 PT 
(14 TPI) CC, and this weighs 5 1/4 oz unboxed.  This is NOS (that's New 
Old Stock) and was not cleaned.  There is nothing to fuss about at all 
other than a few very light scuffs to the finish on the blade.  This is 
factory sharp and straight and they don't get any better than this.  $24.00

http://oldetoolshop.com/forsale/july/saw0702a.jpg
http://oldetoolshop.com/forsale/july/saw0702b.jpg

Tyzack Sons & Turner No 131 8 Inch Gentleman's Steel Back Dovetail Saw. 
Measuring 12 13/16" overall, the blade is 8" long, 1 9/16" high (from 
the teeth to the start of the back), this is sharpened to 15 PT (14 TPI) 
CC, and this weighs 5 1/4 oz unboxed. This is NOS (that's New Old Stock) 
and was not cleaned. There is nothing to fuss about at all other than a 
little bit of extra protective finish on the front of the blade.  This 
is factory sharp and straight and they don't get any better than this. 
$20.00

http://oldetoolshop.com/forsale/may/saw0503a.jpg
http://oldetoolshop.com/forsale/may/saw0503b.jpg

Ridgway No 220 11 Piece Irwin Pattern Auger Bit Set & Roll. The sizes 
are run from 1/4" to 1", and this all weighs 3 lbs 1/2 oz unboxed. 
Ridgway was a long time Sheffield England auger bit maker in business 
from 1878 until they merged with Record in 1975 to become Record 
Ridgway. These just have the Ridgway marks so they were made before that 
time. These are NOS, that's New Old Stock. Note these are straight, any 
bending you see is because of camera lens distortion. I did clean off a 
few small spots of rust they picked up from setting around. The edges, 
lead screws, and tangs are factory fresh. The canvas roll does have a 
couple of rust stains on the inside and a little bit of musty smell to 
it, but it just needs a good airing out. If you are looking for a 
quality set of bits, well you can't do much better than this one.  $55.00

http://oldetoolshop.com/forsale/july/bracebitset0701a.jpg
http://oldetoolshop.com/forsale/july/bracebitset0701b.jpg
http://oldetoolshop.com/forsale/july/bracebitset0701c.jpg
http://oldetoolshop.com/forsale/july/bracebitset0701d.jpg

Rabone Chesterman 10 Inch Sweep Brace.  This weighs 2 lbs 12 1/4 oz 
unboxed.  The Rabone and Chesterman companies merged in 1963 and were in 
business until 1989 when Stanley bought the firm.  This is NOS, that's 
New Old Stock, and was not cleaned.  There is a touch of patina there 
and there from setting around but nothing too bad.  The grip and pad are 
plastic and they have a few dings.  The ratchet and jaws are good, 
although it could stand a touch of oil.  This ain't the fanciest but 
this is a good heavy duty brace.  Note:  I also have an 8" sweep one 
available at the same price.  $24.00

http://oldetoolshop.com/forsale/july/brace0701a.jpg
http://oldetoolshop.com/forsale/july/brace0701b.jpg
http://oldetoolshop.com/forsale/july/brace0701c.jpg
http://oldetoolshop.com/forsale/july/brace0701d.jpg

Four Marples Blue Chip Paring Bench Chisels. Left to right, there is a 
1/4", a 3/8", a 1/2", a 3/4", and they weigh 1 lb 4 1/2 oz unboxed. 
These are NOS (that's New Old Stock) and were not cleaned.  Note: these 
are straight, any bending you see is because of camera lens distortion. 
There is little light funky and couple have some light rust spots from 
laying around but nothing worth kicking the cat over.  The handles have 
some scuffs from being knocked around.  Note: The ones you get might 
vayu slightly from the pictures.  These are quality chisels by one of 
England's top tool makers. $52.00

http://oldetoolshop.com/forsale/june/chiselset0603a.jpg
http://oldetoolshop.com/forsale/june/chiselset0603b.jpg
http://oldetoolshop.com/forsale/june/chiselset0603c.jpg

Stanley No 12-331 9 1/2 Block Plane Blade.  This weighs 2 1/2 oz 
unboxed.  This is NOS, that's New Old Stock and was made in merry olde 
England.  They don't get much better than this.  It sure can't hurt to 
have a spare.  $15.00

http://oldetoolshop.com/forsale/july/planeblade0701a.jpg
http://oldetoolshop.com/forsale/july/planeblade0701b.jpg

NOS Stanley England 12-315 2 3/8 Inch Plane Blade.  This weighs 5 1/2 oz 
unboxed.  This will fit the No. 4 1/2, 5 1/2, 6, and 7 planes except for 
the very early models that had a narrower blade.  This is NOS (that's 
New Old Stock) still in the retail packaging.  They don't get any better 
than this.  $30.00

http://oldetoolshop.com/forsale/june/planeblade0601a.jpg
http://oldetoolshop.com/forsale/june/planeblade0601b.jpg

NOS Stanley England 12-313 2 Inch Plane Blade.  This weighs 4 3/4 oz 
unboxed.  This will fit the No. 4 and 5 planes.  This is NOS (that's New 
Old Stock) still in the retail packaging.  They don't get any better 
than this.  $20.00

http://oldetoolshop.com/forsale/june/planeblade0602a.jpg
http://oldetoolshop.com/forsale/june/planeblade0602b.jpg

Two Lufkin Machinist No 40 Series Calipers. On the left is a 3" No. 41 
outside caliper, on the right is a 4" No. 42 inside caliper, and they 
weigh 2 1/2 oz unboxed. These are NOS, that's New Old Stock. I did clean 
off some oil residue on these (they were oiled at the factory). There is 
a little still up in the joints and there and here. The tips of both of 
them have a few stained spots (these weren't stored very well). Lufkin 
machinist tools are every bit as good as their Starrett and Brown & 
Sharpe cousins.  $20.00

http://oldetoolshop.com/forsale/june/machinisttool0612a.jpg
http://oldetoolshop.com/forsale/june/machinisttool0612b.jpg
http://oldetoolshop.com/forsale/june/machinisttool0612c.jpg

Fine Products England Tool Chisel Roll With 8 Pockets.  Measuring 19 
3/4" long, 14 3/8" high, the pockets vary in width from 1 1/2" to 2 1/2" 
wide, and this weighs 9 oz unboxed.  Made by the H. L. Fine and Son Ltd 
company of Middlesex England.  This is NOS, that's New Old Stock.  This 
was never out of the package until I took it out to take the pretty 
pictures.  Canvas on the outside and some kind of felting on the inside. 
  This is a well made and quality item.  $18.00

http://oldetoolshop.com/forsale/june/toolroll0601a.jpg
http://oldetoolshop.com/forsale/june/toolroll0601b.jpg
http://oldetoolshop.com/forsale/june/toolroll0601c.jpg

Two Cabinetmakers Shave Hooks Or Shavehooks.  These are 7 5/16" long, 
the triangle blade is 2 7/16" across the edges, the other one is 2 3/8" 
high, 1 3/4" wide, and they weigh 9 3/4 oz unboxed.  Not signed as to 
the maker, but I know for a fact that these came over from England in 
the 1980's.  These are NOS, that's New Old Stock.  But they have been 
bouncing around boxes for a while.  I did clean some light patina off of 
the shafts and a few small spots on the blades.  The edges had a few 
light dings that I fixed with some file work.  The handle finish is good 
on both.  These are quality and handy tools.  $15.00

http://oldetoolshop.com/forsale/july/shavehook0702a.jpg
http://oldetoolshop.com/forsale/july/shavehook0702b.jpg
http://oldetoolshop.com/forsale/july/shavehook0702c.jpg

Seven Nicholson 5 Inch Taper Files.  The upper 5 are marked Dbl Ex Slim 
Taper, the lower 2 are marked Slim Taper, they measure 5 1/4" along the 
sides across the teeth and these weigh 6 1/4 oz unboxed.  These are NOS 
(that's New Old Stock).  I did take some rust off of the tangs and a 
couple of the tops.  There are a few light spots of rust on the teeth 
but these are like 99% clean.  These are the ones to have for sharpening 
saws, especially the smaller tooth sized ones, and ya sure ain't gonna 
walk into the local hardware store and purchase files of this quality at 
this kind of price.  $35.00

http://oldetoolshop.com/forsale/july/files0702a.jpg
http://oldetoolshop.com/forsale/july/files0702b.jpg
http://oldetoolshop.com/forsale/july/files0702c.jpg
http://oldetoolshop.com/forsale/july/files0702d.jpg

Working & Collectible Old Tools

Three Millers Falls No 30 Chisels.  The first one is a 3/4", the blade 
is 2 15/16", the middle one is a 1", the blade is 3" long, the last one 
is a 1 1/2", the blade is 3", and they weigh 1 lb 7 oz unboxed.  These 
are in used but reasonably good condition and were cleaned.  The blades 
have couple of dots on the back and the fronts but nothing too bad at 
all.  The edges are good and sharp or pretty darn close.  The red 
Permaloid handles have some scuffs and light wear and somebody drilled 
hanging holes so you won't have to do it.  The striking button on the 
3/4" is banged up a bit, the other two are good.  These ain't perfect 
but they sure ain't bad either and most of these I see look like Buck 
Rogers built two spaceships with them.  Just saying.  $50.00

http://oldetoolshop.com/forsale/july/chiselset0701a.jpg
http://oldetoolshop.com/forsale/july/chiselset0701b.jpg
http://oldetoolshop.com/forsale/july/chiselset0701c.jpg
http://oldetoolshop.com/forsale/july/chiselset0701d.jpg
http://oldetoolshop.com/forsale/july/chiselset0701e.jpg

Set Of Stanley No 71 Router Plane Parts.  There are the knobs and 
threaded rods, the blade clamp, a 9/16" blade, and this all weighs 7 oz 
unboxed.  These are all in used condition and were cleaned.  The knobs 
are the painted hardwood variety and were refinished.  That ain't a 
perfect job but they are better than they were.  There are some dings 
and the one has a partial check along the side.   The nuts on the rods 
have a little wear to the plating on the tops but they remove from the 
rods.  The blade clamp has a little roughness to the plating and some 
light patina inside but it's solid.  The plating on the thumbscrew is 
worn and there is a little pitting but the threads are good.  The blade 
does have some light pitting on the cutting face and some deeper stuff 
on the sides of the shaft.  These ain't minty perfect and they sure 
ain't got a minty perfect price tag but decent parts are better than no 
parts, eh?  Note: I do not have any of the other parts for this plane. 
$55.00

http://oldetoolshop.com/forsale/july/planepart0701a.jpg
http://oldetoolshop.com/forsale/july/planepart0701b.jpg
http://oldetoolshop.com/forsale/july/planepart0701c.jpg
http://oldetoolshop.com/forsale/july/planepart0701d.jpg

A J Wilkinson 8 Inch Folding Handle Drawknife.  Measuring 16 1/8" 
overall, the blade is 8 1/4" long (straight across), 1 1/2" or better 
wide across the edge, and this weighs 1 lb 9 3/4 oz unboxed.  John G. 
Young of Hyde Park, MA was granted Pat. No. 542,721 on July. 16, 1895 
for the design of this tool which was made by A. J. Wilkinson & Co. of 
Boston, MA.  This is in decent condition and was cleaned.  The back of 
the blade has some light pitting right at the edge and some frosting and 
spots on the rest but that is good for the most part.  I did run a file 
over some mushrooming on the back and there are some dings on the top. 
The edge is fairly sharp as is.  The front has some spots of pitting. 
The handles were refinished, that ain't a perfect job but they are 
better than they were.  The plating on the handle arms is worn.  Both 
nuts work and the screws do remove.  This ain't minty but it will get 
the job done.  $50.00

http://oldetoolshop.com/forsale/july/drawknife0701a.jpg
http://oldetoolshop.com/forsale/july/drawknife0701b.jpg
http://oldetoolshop.com/forsale/july/drawknife0701c.jpg
http://oldetoolshop.com/forsale/july/drawknife0701d.jpg

Early Stanley No 62 Marking Gage.  This weighs 4 oz unboxed.  This isn't 
marked other than the patent date but these guys rarely were.  Good ole 
Justus A. Traut of New Britain, CT was granted Pat. No. 334,308 on Jan. 
12, 1886 for the design of the fence used on this tool.  Figuring 20 
years for the use of the patent date, that puts this guy between 112 and 
132 years old.  This is in reasonably good condition and was cleaned by 
someone else.  He also hit it with the shiny stuff.  The beam has some 
dings from the screw and a few stains but nothing too bad in that 
department.  The head also has a few light dings and stains.  The 
locking screw is good.  The screw for the point does remove and the 
point removes as well.  That could stand a quick sharpening but there is 
lots to work with.  This ain't pristine but having seen my share of 
marking gages over the years, these guys rarely are when they get to be 
this old.  $23.00

http://oldetoolshop.com/forsale/july/markinggage0701a.jpg
http://oldetoolshop.com/forsale/july/markinggage0701b.jpg
http://oldetoolshop.com/forsale/july/markinggage0701c.jpg
http://oldetoolshop.com/forsale/july/markinggage0701d.jpg

Vintage Meier Germany 13/16 Inch Barbers Straight Razor.  The blade is 2 
7/8" long across the edge, 13/16" wide across the edge, and this weighs 
1 1/2 oz unboxed.  This is in reasonably good condition and was not 
cleaned.  There are some dots of rust on both sides of the blade but 
nothing too bad.  There is a spot on the top as well.  The edge is good 
with no nicks but it could stand a sharpening.  The handle scales look 
to be celluloid.  Those are good other than a few light scuffs.  The 
joint is a little loose as is the spacer at the end of the handle 
scales.  This ain't perfect but these wider bladed models sure don't 
show up every day.  $30.00

http://oldetoolshop.com/forsale/july/razor0701a.jpg
http://oldetoolshop.com/forsale/july/razor0701b.jpg
http://oldetoolshop.com/forsale/july/razor0701c.jpg

L S Starrett No 38 24 Inch Lock Joint Outside Calipers.  Measuring 24 
13/16" from the tips to the top of the joint and and this weighs 2 lbs 9 
3/4 oz unboxed.  This is in decent condition overall.  It was cleaned by 
someone else.  There are some spots of light pitting and frosting, 
mostly on the front of the arms  The joint lock works as does the fine 
adjustment.  The tips are good with no wear.  This ain't minty but price 
a new one without the lock joint and this is a real deal.  $80.00

http://oldetoolshop.com/forsale/june/machinisttool0615a.jpg
http://oldetoolshop.com/forsale/june/machinisttool0615b.jpg
http://oldetoolshop.com/forsale/june/machinisttool0615c.jpg
http://oldetoolshop.com/forsale/june/machinisttool0615d.jpg

Hand Forged Early Closed End Single Handle Scorp.  Measuring 11 1/8" 
overall, the head is 1 7/8" wide, 1 3/8" high, the cutting area is about 
1" wide at the ends, 15/16" at the center, and this weighs 7 1/4 oz 
unboxed.  Not signed as to the maker.  This is in decent condition 
overall and was cleaned.  The cutting area has some very light pitting 
but nothing too bad.  There is a ding on he edge but this guy is fairly 
sharp.  There is some patina inside the head and on the upper areas and 
the tang.  The handle is the original one.  That has some stains and 
wear and there is a thin check at the top.  I did reseat the hand forged 
iron ring that acts as ferrule, but that might loosen up again.  This 
ain't pretty or perfect but it is a good working tool.  $45.00

http://oldetoolshop.com/forsale/june/earlyscrop0601a.jpg
http://oldetoolshop.com/forsale/june/earlyscrop0601b.jpg
http://oldetoolshop.com/forsale/june/earlyscrop0601c.jpg

Keen Kutter 1/2 Inch Paring Or Bevel Edge Firmer Chisel.  Measuring 8 
5/8" from the edge to the end of the socket, the blade is 6 3/16" long, 
this is 12 1/8" overall, and this weighs 4 1/2 oz unboxed.  This is in 
reasonably good condition and was cleaned.  The back has some very light 
frosting and rust etching but nothing deep at all.  The front is good 
other than some staining and there are user initials after the mark. 
The socket is good but the blade does angle down a little looking from 
the side.  The handle is a replacement.  That is good other than a few 
stains.  This ain't minty but it sure ain't bad and it's got a whole lot 
of blade to work with.  $19.00

http://oldetoolshop.com/forsale/july/chisel0706a.jpg
http://oldetoolshop.com/forsale/july/chisel0706b.jpg

M Myers & Son England Brass Protractor.  Measuring 3 11/16" long, 1 
15/16" high, and this weighs 1/2 oz unboxed.  M Myers & Son were long 
time English makers of pens and drafting tools.  This is in reasonably 
good condition and was cleaned.  The front is good and all the rulings 
are readable.  They are stamped and not just inked on.  The back has a 
few stained spots but nothing too bad.  This is a quality tool, unlike 
the plastic ones you get today. $18.00

http://oldetoolshop.com/forsale/july/draftingtool0702a.jpg
http://oldetoolshop.com/forsale/july/draftingtool0702b.jpg
http://oldetoolshop.com/forsale/july/draftingtool0702c.jpg

L S Starrett No 160 Machinist Toolmaker Clamp Or Vise.  This weighs 6 
1/2 oz unboxed.  This is in decent condition and was cleaned.  There is 
some light patina including some vice jaw marks on the sides.  The jaw 
faces are good, this only has the thin jaw.  The screw threads are good 
and it travels the full distance.  The head has some scuffs and wear to 
the cross hatching.  The base also has some scuffs and wear.  This ain't 
pretty or perfect and it sure ain't got the price tag of a minty one but 
it will get the job done.  $18.00

http://oldetoolshop.com/forsale/july/machinisttool0706a.jpg
http://oldetoolshop.com/forsale/july/machinisttool0706b.jpg
http://oldetoolshop.com/forsale/july/machinisttool0706c.jpg

L S Starrett No 466 A Micrometer Depth Gage.  This weighs 2 1/2 oz 
unboxed.  Good old Laroy S. Starrett of Athol, MA was granted Pat. No. 
726,003 on April 21, 1903 for the design of this tool.  This is in good 
shape and was lightly cleaned.  There ain't much in the way of patina to 
fuss about.  There are some light stained spots on the sides of the base 
but the working face is good.  The micrometer scales are clean and 
readable and this turns freely.  The locking nut for the rod at the top 
also works and the rod removes.  For a tool that is over 100 years old 
(figuring the 20 year limit on patent date markings), this one is right 
nice.  $28.00

http://oldetoolshop.com/forsale/july/machinisttool0705a.jpg
http://oldetoolshop.com/forsale/july/machinisttool0705b.jpg
http://oldetoolshop.com/forsale/july/machinisttool0705c.jpg

L S Starrett No 166 Machinist Pin Vise.  This weighs 1 oz unboxed. 
There is no size mark but it looks to be a B.  This is in used but 
reasonably good condition and was not cleaned.  The chuck and jaws are 
good.  There is a user name on the top of the chuck.  The hard rubber 
handle is a little discolored and has a few dings but that is good to 
go.  This ain't pristine but it will get the job done.  $14.00

http://oldetoolshop.com/forsale/july/machinisttool0702a.jpg
http://oldetoolshop.com/forsale/july/machinisttool0702b.jpg

Craftsman No 5513 Spiral Tapered Brace Reamer.  Measuring 4 3/8" long, 
2" in diameter at the top, and this weighs 6 oz unboxed.  These is in 
used but reasonably good condition and was not cleaned.  There are some 
spots of rust on the insides of the flutes but the edges are good other 
than some very tiny dings.  The tang also has some dings but nothing too 
bad there.  This ain't minty but it will get the job done and it is a 
must have tool for cleaning mushrooming out of the insides of chisel 
sockets.  I have several here that I use all the time.  $17.00

http://oldetoolshop.com/forsale/july/bracetool0701a.jpg
http://oldetoolshop.com/forsale/july/bracetool0701b.jpg

Millers Falls No 214 Saw Set Or Sawset.  This weighs 1 lb 4 oz unboxed. 
  This isn't marked but it is a 214 with the Sears paint job.  Identical 
tool, slightly different color scheme.  This is in used but reasonably 
good shape and was cleaned.  This has all of the original finish but 
there is some staining mainly on the front handle.  The plunger tip is 
good and the anvil doesn't show much in the way of wear.  That is marked 
from 4 to 16 as far as TPI goes.  The screw on that works and was oiled 
as was the fence screw.  This ain't the fanciest, but for the money, it 
sure ain't bad.  $20.00

http://oldetoolshop.com/forsale/july/sawset0701a.jpg
http://oldetoolshop.com/forsale/july/sawset0701b.jpg
http://oldetoolshop.com/forsale/july/sawset0701c.jpg

Millers Falls No 206 Steel Body Block Plane.  This weighs 1 lb 1/4 oz 
unboxed.  This model was made between 1940 and 1959.  This is in used 
but reasonably good condition and was cleaned.  Note this is straight, 
any bending you see is because of camera lens distortion, although why 
folks would think that I would sell a bent plane is beyond me.  The 
sides have some frosting and a few dings.  The sole also has some 
frosting and some scratches but nothing too there.  The body finish is 
original and close to perfect other than some dings on the tops of the 
sides and at the heel.  The cap is good.  The blade is clean other than 
some scratches on the cutting face and there is lots to work with.  The 
blade will need a sharpening.  All the screws work and were oiled.  This 
ain't minty perfect but seeing as how most of these went to trade 
schools, well this one sure is better than most of them that show up. 
$22.00

http://oldetoolshop.com/forsale/july/millersfalls2060701a.jpg
http://oldetoolshop.com/forsale/july/millersfalls2060701b.jpg
http://oldetoolshop.com/forsale/july/millersfalls2060701c.jpg
http://oldetoolshop.com/forsale/july/millersfalls2060701d.jpg

Two Vintage Wooden Level Sights.  They measure 1 7/8" long, 1 3/8" wide, 
1 5/16" across the inside of the clamp area, and they weigh 3 1/4 oz 
unboxed.  Not signed as to the maker, these ain't Stanley No. 1's unless 
they changed the base area at some point and didn't bother to tell me. 
These are in decent condition and were cleaned.  There is some wear to 
the finish but most of it is there.  The screws that lock these to the 
level are good and the sight window and reference line are good,  These 
ain't the fanciest but these guys sure don't show up very often.  $24.00

http://oldetoolshop.com/forsale/july/levelsights0701a.jpg
http://oldetoolshop.com/forsale/july/levelsights0701b.jpg
http://oldetoolshop.com/forsale/july/levelsights0701c.jpg

Buck Brothers 1/4 Inch Gouge.  Measuring 4 9/16" from the edge to the 
top of the handle, the blade is 3 3/8" long, 1/4" wide across the inside 
of the sweep, this is 9 1/2" overall, and this weighs 2 oz unboxed. 
This is in decent condition overall and was cleaned.  Inside of the 
sweep is good other than some very light frosting.  The back is good for 
the first half and could be used if you wanted to flip the bevel, after 
that there is some light stuff.  The handle is the original one.  That 
has some wear, staining and there is some chipping at the striking end, 
but it's solid enough.  This ain't pretty or perfect but it will get the 
job done.  $15.00

http://oldetoolshop.com/forsale/july/chisel0705a.jpg
http://oldetoolshop.com/forsale/july/chisel0705b.jpg

Vintage Sargent 8 Inch Steel Wing Compass Or Divider.  Measuring 8 1/2" 
long and this weighs 5 oz unboxed.  This is in reasonably good condition 
and was cleaned.  There is a little patina there and here, mostly on the 
insides of the arms where the wing is located.  The joint is good and 
the locking screw and fine adjustment nut both work.  The tips are sharp 
and good to go.  These guys were mainly made for trade schools but it is 
a good working tool.  $18.00

http://oldetoolshop.com/forsale/july/divider0701a.jpg
http://oldetoolshop.com/forsale/july/divider0701b.jpg
http://oldetoolshop.com/forsale/july/divider0701c.jpg

Old Hand Forged Farrier Ball Jaw Blacksmith Tongs.  Measuring 14 1/4" 
long, the jaws are 1 3/8" deep, 1 1/8" wide, and this weighs 1 lb 9 3/4 
oz unboxed.  Not signed as to the maker.  This is in decent condition 
and was cleaned (oh yeah!)  There is some overall pitting.  The jaws are 
good other than the patina. They don't close down tight but that could 
be fixed by adjusting the handles a little (which is best done with a 
little heat).  The joint has some wiggle but it ain't gonna fall again. 
The handles are good.  This ain't the prettiest but it will get the job 
done.  $22.00

http://oldetoolshop.com/forsale/july/blacksmith0704a.jpg
http://oldetoolshop.com/forsale/july/blacksmith0704b.jpg
http://oldetoolshop.com/forsale/july/blacksmith0704c.jpg

Early Hand Forged Small Face Blacksmith Flatter.  Measuring 8 7/8" 
overall, the head is 2 11/16" long, the face is 1 5/8" wide, 1 1/2" 
high, and this weighs 1 lb 5 oz unboxed.  Not signed as to the maker. 
This is in decent condition and was cleaned.  There is lots of patina on 
the head (that's how I know it's early eh?)  The face has some dings, 
mushrooming on the sides, and is slightly rounded from wear.  The 
striking end has some chips, a little mushrooming, and I did zing off 
one sharp bit on the one corner.  The handle is old and has the usual 
stains and a couple of long dead worm holes.  That is just shoved into 
the eye and the head wiggles a little, but it's better than no handle 
(unless you want a 2ft one..)  This ain't minty but it does have some 
serious age to it and it sure ain't ready for the scrap pile just yet. 
$26.00

http://oldetoolshop.com/forsale/july/blacksmith0702a.jpg
http://oldetoolshop.com/forsale/july/blacksmith0702b.jpg
http://oldetoolshop.com/forsale/july/blacksmith0702c.jpg
http://oldetoolshop.com/forsale/july/blacksmith0702d.jpg

Colwell Cooperage Co Nantucket Style Coopers Hoop Driver.  Measuring 10 
5/8" overall, the head is 5 1/16" long, the face is 1 1/16" in diameter, 
the driver is 1 7/16" high, 3/16" wide across the outside, and this 
weighs 1 lb 8 3/4  oz unboxed.  The Colwell Cooperage Co is listed as 
being in Jersey City NJ, and New York City (this has the New York mark). 
  There isn't much as far as working dates, I see some stuff from the 
early 1900's up to the 1920s.  This is in reasonably good condition for 
the age and use and was cleaned.  There are some pitted spots on the 
head but overall that is good.  The top has some marks from being 
knocked back on the handle.  The face has some dings but it's not as 
bashed up as a lot of these guys that you see.  The driver groove has 
some dings on the edges but it's still deep enough to use.  The handle 
is old and probably the original one.  That has some stains and age 
checks but it feels solid.  The head is loose but ain't gonna come off. 
These guys sure don't show up much at all by this maker.  The last photo 
has the Colwell catalog page section for this tool, just in case any of 
you "experts" want to tell me it's a blacksmith tool.  Just saying.  $35.00

http://oldetoolshop.com/forsale/july/cooperstool0701a.jpg
http://oldetoolshop.com/forsale/july/cooperstool0701b.jpg
http://oldetoolshop.com/forsale/july/cooperstool0701c.jpg
http://oldetoolshop.com/forsale/july/cooperstool0701d.jpg

Early Hand Forged Ball Peen Hammer.  Measuring 12 3/16" overall, the 
head is 4 1/4" long, the face is 15/16"  wide, 7/8" high, the peen is 1" 
in diameter, and this weighs 1 lb 2 3/4 oz unboxed.  Not signed as to 
the maker.  This is in reasonably good condition and was cleaned.  There 
ain't much in the way of patina on the head.  The face and peen have 
some tiny dings but nothing too bad there.  The handle was put on by 
someone else and they left some scuff marks on the top of the eye.  The 
handle has a few stains but it's solid and on tight.  I gotta say, that 
I sure don't see too many of these old dawgs around in this kind of 
shape.  $24.00

http://oldetoolshop.com/forsale/july/hammer0701a.jpg
http://oldetoolshop.com/forsale/july/hammer0701b.jpg
http://oldetoolshop.com/forsale/july/hammer0701c.jpg

Vintage James Swan Timber Framer T-Auger Handle.  Measuring 14 7/8" long 
and this weighs 1 lb 6 1/4 oz unboxed.  This is in decent condition and 
was cleaned.  The head has some frosting but nothing too bad patina 
wise.  There is some crusty inside that I couldn't get to.  The tang 
clamp is good, the screw works and was oiled.  The handles have some 
dings, stains, and wear, but they are solid with no cracks.  Both of 
them do unscrew from the head.  This ain't minty but it will get the job 
done.  $24.00

http://oldetoolshop.com/forsale/july/augerhandle0701a.jpg
http://oldetoolshop.com/forsale/july/augerhandle0701b.jpg
http://oldetoolshop.com/forsale/july/augerhandle0701c.jpg
http://oldetoolshop.com/forsale/july/augerhandle0701d.jpg

Stone Mason Early Hand Forged Bush Dressing Hammer Head.  Measuring 5 
3/16" long, the one face is 1 5/16" wide, 9/16" high, the other face is 
1 3/8" wide, about 1/2" high, and this weighs 1 lb 6 oz unboxed.  Not 
signed as to the maker.  This is in decent condition and was cleaned. 
There is the usual patina found on these tools but nothing too bad. 
Both faces have a few small chips on the edges and a couple of dings. 
The ridges on the faces are slightly rounded but that's how this guy was 
made.  The eye is good to go.  These guys are sure getting few and far 
between, at least around these here parts.  $22.00

http://oldetoolshop.com/forsale/july/stonetool0701a.jpg
http://oldetoolshop.com/forsale/july/stonetool0701b.jpg
http://oldetoolshop.com/forsale/july/stonetool0701c.jpg

Old Orphan Stanley No 4 Trammel Point With Pencil Holder.  This weighs 2 
1/4 oz unboxed.  This is in reasonably good condition and was cleaned by 
someone else.  The finish on the body is good and the point is also 
good.  The beam screw works and travels the full distance.  The pencil 
screw has a little patina on the threads but that works.  I didn't get 
the other trammel to go with this but you might have one in your junk 
boxes and together these are very collectible.  $15.00

http://oldetoolshop.com/forsale/july/trammelpoint0701a.jpg
http://oldetoolshop.com/forsale/july/trammelpoint0701b.jpg
http://oldetoolshop.com/forsale/july/trammelpoint0701c.jpg

A Set Vintage of 1/8 Inch Steel Number Stamps With Box.  This weighs 11 
1/4 oz unboxed.  These are marked as shown in the picture.  The figures 
are like a Courier font.  These are in used but good shape and were not 
cleaned.  The 0 figure has a little wear, the rest are good.  The 
striking ends have a few light dings but nothing too bad there.  The box 
has some staining and a few dings but it's solid.  These ain't minty 
perfect but they sure ain't bad either.  $23.00

http://oldetoolshop.com/forsale/july/stampset0701a.jpg
http://oldetoolshop.com/forsale/july/stampset0701b.jpg
http://oldetoolshop.com/forsale/july/stampset0701c.jpg

Early Hand Forged Adze Eye Cross Peen Hammer.  Measuring 13 15/16" 
overall, the head is 4 15/16" long, the face is 1/2" in diameter, the 
peen is 9/16" wide, and this weighs 12 3/4 oz unboxed.  There is a user 
name stamped on the side of the eye which might be the maker.  This is 
in decent condition overall and was cleaned.  The head has some light 
patina.  The face is good other than some scuff marks and was dressed at 
some point to get rid of some mushrooming around the edge.  The peen is 
good other than some dings.  There is a line on the top and underside of 
the peen but it's not cracked, just something that was left over when 
this was forged.  There is a crack on the lower front edge of the adze 
style eye but it doesn't run too deep.  The oval handle is the original 
one.  That has some dings and stains.  The head wiggles a little but 
it's not going to come off.  This is what it is, but these guys sure 
don't show up very often with the original handle.  $22.00

http://oldetoolshop.com/forsale/july/earlyhammer0701a.jpg
http://oldetoolshop.com/forsale/july/earlyhammer0701b.jpg
http://oldetoolshop.com/forsale/july/earlyhammer0701c.jpg
http://oldetoolshop.com/forsale/july/earlyhammer0701d.jpg

Vintage Ward 5/16 Inch Firmer Carving Chisel.  Measuring 4 1/4" from the 
edge to the top of the handle, the blade is 3 1/4" long, this is 9 7/16" 
overall, and this weighs 2 3/4 oz unboxed.  This has the Ward mark and 
the Ward & Payne trademark.  This is in reasonably good condition and 
was cleaned.  The back has some frosting and staining but nothing too 
bad.  The front also has some light patina.  The edge has a few small 
chips but this will need a sharping anyways.  The handle is good other 
than a few light dings and stains and a couple of dings on the end 
leather washer.  This is a quality English edge tool.  $17.00

http://oldetoolshop.com/forsale/july/chisel0702a.jpg
http://oldetoolshop.com/forsale/july/chisel0702b.jpg

---------------------------------------------
“When you're at the end of your rope, tie a knot and hold on.”

Theodore Roosevelt

Tony

Olde River Hard Goods
http://www.oldetoolshop.com
TSMusic on Facebook
http://www.facebook.com/tonyseomusic

266113	Anthony Seo	2018‑07‑16	FS: July Jewels List B
Summer is in full bloom. There are a bunch of fresh goodies on the list and some good stuff in the NOS section. There ain't an infinite supply of these items so don't wait. PayPal is now accepted and preferred (if you use it) on all items. On items less than $25 (not including shipping) I would appreciate you using the Send Money to Family & Friends option so I don't get killed with the fees but that is your call. Checks and money orders are still welcome, it just seems that 1st Class letters seem to be taking forever to get from there to here. And remember........da more ya buy, the cheaper they fly! First contact (that is e-mail, or phone) that says I want it gets it. Oldtools terms, except on items and orders over $100, if I don't know ya or haven't done business in the past (and my records good way back..) then it's pre-pay. I do take PayPal (except as noted). Prices do not include shipping. All items are shipped with Delivery Confirmation. Insurance, unless it is a big order or a very fragile item is optional. Just let me know. Also, I am shipping a lot more stuff via First Class mail. There will be a small amount added to the shipping cover the cost of the padded mailer. I don't get them for free. Please put your name and address in the message. Saves time and email traffic! --------------------------------------------------- Tyzack Turner No 660 Talisman 24 Inch 7 PT Cross Cut Saw NOS Quality Tool Tyzack Turner No 660 Talisman 24 Inch 7 PT Cross Cut Saw. This weighs 1 lb 9 oz unboxed. This is NOS, that's New Old Stock, and was not cleaned. There ain't nothing at all to fuss about with this guy. The blade is shiny and sharp. There is a little bit of the protective coating showing at the toe. The tote and saw nuts are as good as they get. This is a quality tool made by an well respected English saw maker and I have been selling and shipping saws now for over 24 years so I know what I'm talking about. $45.00 http://oldetoolshop.com/forsale/july/saw0701a.jpg http://oldetoolshop.com/forsale/july/saw0701b.jpg http://oldetoolshop.com/forsale/july/saw0701c.jpg http://oldetoolshop.com/forsale/july/saw0701d.jpg http://oldetoolshop.com/forsale/july/saw0701e.jpg Tyzack Turner No 166 Talisman 10 Inch 13 PT Tenon Saw. This weighs 1 lb 3 1/2 oz unboxed. This is NOS, that's New Old Stock, and was not cleaned. There are some spots of funky on the brass back from being stored but the blade is factory bright. The handle finish is perfect. There also is a little funky on the one sawnut on the front and some on the nuts on the back, (these weren't stored in a very nice place.) Nothing worth kicking the cat over. If you are looking for a top quality back saw, you can't do much better than this for the price. $60.00 http://oldetoolshop.com/forsale/june/saw0606a.jpg http://oldetoolshop.com/forsale/june/saw0606b.jpg http://oldetoolshop.com/forsale/june/saw0606c.jpg http://oldetoolshop.com/forsale/june/saw0606d.jpg NOS Tyzack Sons & Turner No 130 8 Inch Gentleman's Brass Back Dovetail Saw. Measuring 12 13/16" overall, the blade is 8" long, 1 9/16" high (from the teeth to the start of the back), this is sharpened to 15 PT (14 TPI) CC, and this weighs 5 1/4 oz unboxed. This is NOS (that's New Old Stock) and was not cleaned. There is nothing to fuss about at all other than a few very light scuffs to the finish on the blade. This is factory sharp and straight and they don't get any better than this. $24.00 http://oldetoolshop.com/forsale/july/saw0702a.jpg http://oldetoolshop.com/forsale/july/saw0702b.jpg Tyzack Sons & Turner No 131 8 Inch Gentleman's Steel Back Dovetail Saw. Measuring 12 13/16" overall, the blade is 8" long, 1 9/16" high (from the teeth to the start of the back), this is sharpened to 15 PT (14 TPI) CC, and this weighs 5 1/4 oz unboxed. This is NOS (that's New Old Stock) and was not cleaned. There is nothing to fuss about at all other than a little bit of extra protective finish on the front of the blade. This is factory sharp and straight and they don't get any better than this. $20.00 http://oldetoolshop.com/forsale/may/saw0503a.jpg http://oldetoolshop.com/forsale/may/saw0503b.jpg Ridgway No 220 11 Piece Irwin Pattern Auger Bit Set & Roll. The sizes are run from 1/4" to 1", and this all weighs 3 lbs 1/2 oz unboxed. Ridgway was a long time Sheffield England auger bit maker in business from 1878 until they merged with Record in 1975 to become Record Ridgway. These just have the Ridgway marks so they were made before that time. These are NOS, that's New Old Stock. Note these are straight, any bending you see is because of camera lens distortion. I did clean off a few small spots of rust they picked up from setting around. The edges, lead screws, and tangs are factory fresh. The canvas roll does have a couple of rust stains on the inside and a little bit of musty smell to it, but it just needs a good airing out. If you are looking for a quality set of bits, well you can't do much better than this one. $55.00 http://oldetoolshop.com/forsale/july/bracebitset0701a.jpg http://oldetoolshop.com/forsale/july/bracebitset0701b.jpg http://oldetoolshop.com/forsale/july/bracebitset0701c.jpg http://oldetoolshop.com/forsale/july/bracebitset0701d.jpg Rabone Chesterman 10 Inch Sweep Brace. This weighs 2 lbs 12 1/4 oz unboxed. The Rabone and Chesterman companies merged in 1963 and were in business until 1989 when Stanley bought the firm. This is NOS, that's New Old Stock, and was not cleaned. There is a touch of patina there and there from setting around but nothing too bad. The grip and pad are plastic and they have a few dings. The ratchet and jaws are good, although it could stand a touch of oil. This ain't the fanciest but this is a good heavy duty brace. Note: I also have an 8" sweep one available at the same price. $24.00 http://oldetoolshop.com/forsale/july/brace0701a.jpg http://oldetoolshop.com/forsale/july/brace0701b.jpg http://oldetoolshop.com/forsale/july/brace0701c.jpg http://oldetoolshop.com/forsale/july/brace0701d.jpg Four Marples Blue Chip Paring Bench Chisels. Left to right, there is a 1/4", a 3/8", a 1/2", a 3/4", and they weigh 1 lb 4 1/2 oz unboxed. These are NOS (that's New Old Stock) and were not cleaned. Note: these are straight, any bending you see is because of camera lens distortion. There is little light funky and couple have some light rust spots from laying around but nothing worth kicking the cat over. The handles have some scuffs from being knocked around. Note: The ones you get might vayu slightly from the pictures. These are quality chisels by one of England's top tool makers. $52.00 http://oldetoolshop.com/forsale/june/chiselset0603a.jpg http://oldetoolshop.com/forsale/june/chiselset0603b.jpg http://oldetoolshop.com/forsale/june/chiselset0603c.jpg Stanley No 12-331 9 1/2 Block Plane Blade. This weighs 2 1/2 oz unboxed. This is NOS, that's New Old Stock and was made in merry olde England. They don't get much better than this. It sure can't hurt to have a spare. $15.00 http://oldetoolshop.com/forsale/july/planeblade0701a.jpg http://oldetoolshop.com/forsale/july/planeblade0701b.jpg NOS Stanley England 12-315 2 3/8 Inch Plane Blade. This weighs 5 1/2 oz unboxed. This will fit the No. 4 1/2, 5 1/2, 6, and 7 planes except for the very early models that had a narrower blade. This is NOS (that's New Old Stock) still in the retail packaging. They don't get any better than this. $30.00 http://oldetoolshop.com/forsale/june/planeblade0601a.jpg http://oldetoolshop.com/forsale/june/planeblade0601b.jpg NOS Stanley England 12-313 2 Inch Plane Blade. This weighs 4 3/4 oz unboxed. This will fit the No. 4 and 5 planes. This is NOS (that's New Old Stock) still in the retail packaging. They don't get any better than this. $20.00 http://oldetoolshop.com/forsale/june/planeblade0602a.jpg http://oldetoolshop.com/forsale/june/planeblade0602b.jpg Two Lufkin Machinist No 40 Series Calipers. On the left is a 3" No. 41 outside caliper, on the right is a 4" No. 42 inside caliper, and they weigh 2 1/2 oz unboxed. These are NOS, that's New Old Stock. I did clean off some oil residue on these (they were oiled at the factory). There is a little still up in the joints and there and here. The tips of both of them have a few stained spots (these weren't stored very well). Lufkin machinist tools are every bit as good as their Starrett and Brown & Sharpe cousins. $20.00 http://oldetoolshop.com/forsale/june/machinisttool0612a.jpg http://oldetoolshop.com/forsale/june/machinisttool0612b.jpg http://oldetoolshop.com/forsale/june/machinisttool0612c.jpg Fine Products England Tool Chisel Roll With 8 Pockets. Measuring 19 3/4" long, 14 3/8" high, the pockets vary in width from 1 1/2" to 2 1/2" wide, and this weighs 9 oz unboxed. Made by the H. L. Fine and Son Ltd company of Middlesex England. This is NOS, that's New Old Stock. This was never out of the package until I took it out to take the pretty pictures. Canvas on the outside and some kind of felting on the inside. This is a well made and quality item. $18.00 http://oldetoolshop.com/forsale/june/toolroll0601a.jpg http://oldetoolshop.com/forsale/june/toolroll0601b.jpg http://oldetoolshop.com/forsale/june/toolroll0601c.jpg Two Cabinetmakers Shave Hooks Or Shavehooks. These are 7 5/16" long, the triangle blade is 2 7/16" across the edges, the other one is 2 3/8" high, 1 3/4" wide, and they weigh 9 3/4 oz unboxed. Not signed as to the maker, but I know for a fact that these came over from England in the 1980's. These are NOS, that's New Old Stock. But they have been bouncing around boxes for a while. I did clean some light patina off of the shafts and a few small spots on the blades. The edges had a few light dings that I fixed with some file work. The handle finish is good on both. These are quality and handy tools. $15.00 http://oldetoolshop.com/forsale/july/shavehook0702a.jpg http://oldetoolshop.com/forsale/july/shavehook0702b.jpg http://oldetoolshop.com/forsale/july/shavehook0702c.jpg Seven Nicholson 5 Inch Taper Files. The upper 5 are marked Dbl Ex Slim Taper, the lower 2 are marked Slim Taper, they measure 5 1/4" along the sides across the teeth and these weigh 6 1/4 oz unboxed. These are NOS (that's New Old Stock). I did take some rust off of the tangs and a couple of the tops. There are a few light spots of rust on the teeth but these are like 99% clean. These are the ones to have for sharpening saws, especially the smaller tooth sized ones, and ya sure ain't gonna walk into the local hardware store and purchase files of this quality at this kind of price. $35.00 http://oldetoolshop.com/forsale/july/files0702a.jpg http://oldetoolshop.com/forsale/july/files0702b.jpg http://oldetoolshop.com/forsale/july/files0702c.jpg http://oldetoolshop.com/forsale/july/files0702d.jpg Working & Collectible Old Tools Three Millers Falls No 30 Chisels. The first one is a 3/4", the blade is 2 15/16", the middle one is a 1", the blade is 3" long, the last one is a 1 1/2", the blade is 3", and they weigh 1 lb 7 oz unboxed. These are in used but reasonably good condition and were cleaned. The blades have couple of dots on the back and the fronts but nothing too bad at all. The edges are good and sharp or pretty darn close. The red Permaloid handles have some scuffs and light wear and somebody drilled hanging holes so you won't have to do it. The striking button on the 3/4" is banged up a bit, the other two are good. These ain't perfect but they sure ain't bad either and most of these I see look like Buck Rogers built two spaceships with them. Just saying. $50.00 http://oldetoolshop.com/forsale/july/chiselset0701a.jpg http://oldetoolshop.com/forsale/july/chiselset0701b.jpg http://oldetoolshop.com/forsale/july/chiselset0701c.jpg http://oldetoolshop.com/forsale/july/chiselset0701d.jpg http://oldetoolshop.com/forsale/july/chiselset0701e.jpg Set Of Stanley No 71 Router Plane Parts. There are the knobs and threaded rods, the blade clamp, a 9/16" blade, and this all weighs 7 oz unboxed. These are all in used condition and were cleaned. The knobs are the painted hardwood variety and were refinished. That ain't a perfect job but they are better than they were. There are some dings and the one has a partial check along the side. The nuts on the rods have a little wear to the plating on the tops but they remove from the rods. The blade clamp has a little roughness to the plating and some light patina inside but it's solid. The plating on the thumbscrew is worn and there is a little pitting but the threads are good. The blade does have some light pitting on the cutting face and some deeper stuff on the sides of the shaft. These ain't minty perfect and they sure ain't got a minty perfect price tag but decent parts are better than no parts, eh? Note: I do not have any of the other parts for this plane. $55.00 http://oldetoolshop.com/forsale/july/planepart0701a.jpg http://oldetoolshop.com/forsale/july/planepart0701b.jpg http://oldetoolshop.com/forsale/july/planepart0701c.jpg http://oldetoolshop.com/forsale/july/planepart0701d.jpg A J Wilkinson 8 Inch Folding Handle Drawknife. Measuring 16 1/8" overall, the blade is 8 1/4" long (straight across), 1 1/2" or better wide across the edge, and this weighs 1 lb 9 3/4 oz unboxed. John G. Young of Hyde Park, MA was granted Pat. No. 542,721 on July. 16, 1895 for the design of this tool which was made by A. J. Wilkinson & Co. of Boston, MA. This is in decent condition and was cleaned. The back of the blade has some light pitting right at the edge and some frosting and spots on the rest but that is good for the most part. I did run a file over some mushrooming on the back and there are some dings on the top. The edge is fairly sharp as is. The front has some spots of pitting. The handles were refinished, that ain't a perfect job but they are better than they were. The plating on the handle arms is worn. Both nuts work and the screws do remove. This ain't minty but it will get the job done. $50.00 http://oldetoolshop.com/forsale/july/drawknife0701a.jpg http://oldetoolshop.com/forsale/july/drawknife0701b.jpg http://oldetoolshop.com/forsale/july/drawknife0701c.jpg http://oldetoolshop.com/forsale/july/drawknife0701d.jpg Early Stanley No 62 Marking Gage. This weighs 4 oz unboxed. This isn't marked other than the patent date but these guys rarely were. Good ole Justus A. Traut of New Britain, CT was granted Pat. No. 334,308 on Jan. 12, 1886 for the design of the fence used on this tool. Figuring 20 years for the use of the patent date, that puts this guy between 112 and 132 years old. This is in reasonably good condition and was cleaned by someone else. He also hit it with the shiny stuff. The beam has some dings from the screw and a few stains but nothing too bad in that department. The head also has a few light dings and stains. The locking screw is good. The screw for the point does remove and the point removes as well. That could stand a quick sharpening but there is lots to work with. This ain't pristine but having seen my share of marking gages over the years, these guys rarely are when they get to be this old. $23.00 http://oldetoolshop.com/forsale/july/markinggage0701a.jpg http://oldetoolshop.com/forsale/july/markinggage0701b.jpg http://oldetoolshop.com/forsale/july/markinggage0701c.jpg http://oldetoolshop.com/forsale/july/markinggage0701d.jpg Vintage Meier Germany 13/16 Inch Barbers Straight Razor. The blade is 2 7/8" long across the edge, 13/16" wide across the edge, and this weighs 1 1/2 oz unboxed. This is in reasonably good condition and was not cleaned. There are some dots of rust on both sides of the blade but nothing too bad. There is a spot on the top as well. The edge is good with no nicks but it could stand a sharpening. The handle scales look to be celluloid. Those are good other than a few light scuffs. The joint is a little loose as is the spacer at the end of the handle scales. This ain't perfect but these wider bladed models sure don't show up every day. $30.00 http://oldetoolshop.com/forsale/july/razor0701a.jpg http://oldetoolshop.com/forsale/july/razor0701b.jpg http://oldetoolshop.com/forsale/july/razor0701c.jpg L S Starrett No 38 24 Inch Lock Joint Outside Calipers. Measuring 24 13/16" from the tips to the top of the joint and and this weighs 2 lbs 9 3/4 oz unboxed. This is in decent condition overall. It was cleaned by someone else. There are some spots of light pitting and frosting, mostly on the front of the arms The joint lock works as does the fine adjustment. The tips are good with no wear. This ain't minty but price a new one without the lock joint and this is a real deal. $80.00 http://oldetoolshop.com/forsale/june/machinisttool0615a.jpg http://oldetoolshop.com/forsale/june/machinisttool0615b.jpg http://oldetoolshop.com/forsale/june/machinisttool0615c.jpg http://oldetoolshop.com/forsale/june/machinisttool0615d.jpg Hand Forged Early Closed End Single Handle Scorp. Measuring 11 1/8" overall, the head is 1 7/8" wide, 1 3/8" high, the cutting area is about 1" wide at the ends, 15/16" at the center, and this weighs 7 1/4 oz unboxed. Not signed as to the maker. This is in decent condition overall and was cleaned. The cutting area has some very light pitting but nothing too bad. There is a ding on he edge but this guy is fairly sharp. There is some patina inside the head and on the upper areas and the tang. The handle is the original one. That has some stains and wear and there is a thin check at the top. I did reseat the hand forged iron ring that acts as ferrule, but that might loosen up again. This ain't pretty or perfect but it is a good working tool. $45.00 http://oldetoolshop.com/forsale/june/earlyscrop0601a.jpg http://oldetoolshop.com/forsale/june/earlyscrop0601b.jpg http://oldetoolshop.com/forsale/june/earlyscrop0601c.jpg Keen Kutter 1/2 Inch Paring Or Bevel Edge Firmer Chisel. Measuring 8 5/8" from the edge to the end of the socket, the blade is 6 3/16" long, this is 12 1/8" overall, and this weighs 4 1/2 oz unboxed. This is in reasonably good condition and was cleaned. The back has some very light frosting and rust etching but nothing deep at all. The front is good other than some staining and there are user initials after the mark. The socket is good but the blade does angle down a little looking from the side. The handle is a replacement. That is good other than a few stains. This ain't minty but it sure ain't bad and it's got a whole lot of blade to work with. $19.00 http://oldetoolshop.com/forsale/july/chisel0706a.jpg http://oldetoolshop.com/forsale/july/chisel0706b.jpg M Myers & Son England Brass Protractor. Measuring 3 11/16" long, 1 15/16" high, and this weighs 1/2 oz unboxed. M Myers & Son were long time English makers of pens and drafting tools. This is in reasonably good condition and was cleaned. The front is good and all the rulings are readable. They are stamped and not just inked on. The back has a few stained spots but nothing too bad. This is a quality tool, unlike the plastic ones you get today. $18.00 http://oldetoolshop.com/forsale/july/draftingtool0702a.jpg http://oldetoolshop.com/forsale/july/draftingtool0702b.jpg http://oldetoolshop.com/forsale/july/draftingtool0702c.jpg L S Starrett No 160 Machinist Toolmaker Clamp Or Vise. This weighs 6 1/2 oz unboxed. This is in decent condition and was cleaned. There is some light patina including some vice jaw marks on the sides. The jaw faces are good, this only has the thin jaw. The screw threads are good and it travels the full distance. The head has some scuffs and wear to the cross hatching. The base also has some scuffs and wear. This ain't pretty or perfect and it sure ain't got the price tag of a minty one but it will get the job done. $18.00 http://oldetoolshop.com/forsale/july/machinisttool0706a.jpg http://oldetoolshop.com/forsale/july/machinisttool0706b.jpg http://oldetoolshop.com/forsale/july/machinisttool0706c.jpg L S Starrett No 466 A Micrometer Depth Gage. This weighs 2 1/2 oz unboxed. Good old Laroy S. Starrett of Athol, MA was granted Pat. No. 726,003 on April 21, 1903 for the design of this tool. This is in good shape and was lightly cleaned. There ain't much in the way of patina to fuss about. There are some light stained spots on the sides of the base but the working face is good. The micrometer scales are clean and readable and this turns freely. The locking nut for the rod at the top also works and the rod removes. For a tool that is over 100 years old (figuring the 20 year limit on patent date markings), this one is right nice. $28.00 http://oldetoolshop.com/forsale/july/machinisttool0705a.jpg http://oldetoolshop.com/forsale/july/machinisttool0705b.jpg http://oldetoolshop.com/forsale/july/machinisttool0705c.jpg L S Starrett No 166 Machinist Pin Vise. This weighs 1 oz unboxed. There is no size mark but it looks to be a B. This is in used but reasonably good condition and was not cleaned. The chuck and jaws are good. There is a user name on the top of the chuck. The hard rubber handle is a little discolored and has a few dings but that is good to go. This ain't pristine but it will get the job done. $14.00 http://oldetoolshop.com/forsale/july/machinisttool0702a.jpg http://oldetoolshop.com/forsale/july/machinisttool0702b.jpg Craftsman No 5513 Spiral Tapered Brace Reamer. Measuring 4 3/8" long, 2" in diameter at the top, and this weighs 6 oz unboxed. These is in used but reasonably good condition and was not cleaned. There are some spots of rust on the insides of the flutes but the edges are good other than some very tiny dings. The tang also has some dings but nothing too bad there. This ain't minty but it will get the job done and it is a must have tool for cleaning mushrooming out of the insides of chisel sockets. I have several here that I use all the time. $17.00 http://oldetoolshop.com/forsale/july/bracetool0701a.jpg http://oldetoolshop.com/forsale/july/bracetool0701b.jpg Millers Falls No 214 Saw Set Or Sawset. This weighs 1 lb 4 oz unboxed. This isn't marked but it is a 214 with the Sears paint job. Identical tool, slightly different color scheme. This is in used but reasonably good shape and was cleaned. This has all of the original finish but there is some staining mainly on the front handle. The plunger tip is good and the anvil doesn't show much in the way of wear. That is marked from 4 to 16 as far as TPI goes. The screw on that works and was oiled as was the fence screw. This ain't the fanciest, but for the money, it sure ain't bad. $20.00 http://oldetoolshop.com/forsale/july/sawset0701a.jpg http://oldetoolshop.com/forsale/july/sawset0701b.jpg http://oldetoolshop.com/forsale/july/sawset0701c.jpg Millers Falls No 206 Steel Body Block Plane. This weighs 1 lb 1/4 oz unboxed. This model was made between 1940 and 1959. This is in used but reasonably good condition and was cleaned. Note this is straight, any bending you see is because of camera lens distortion, although why folks would think that I would sell a bent plane is beyond me. The sides have some frosting and a few dings. The sole also has some frosting and some scratches but nothing too there. The body finish is original and close to perfect other than some dings on the tops of the sides and at the heel. The cap is good. The blade is clean other than some scratches on the cutting face and there is lots to work with. The blade will need a sharpening. All the screws work and were oiled. This ain't minty perfect but seeing as how most of these went to trade schools, well this one sure is better than most of them that show up. $22.00 http://oldetoolshop.com/forsale/july/millersfalls2060701a.jpg http://oldetoolshop.com/forsale/july/millersfalls2060701b.jpg http://oldetoolshop.com/forsale/july/millersfalls2060701c.jpg http://oldetoolshop.com/forsale/july/millersfalls2060701d.jpg Two Vintage Wooden Level Sights. They measure 1 7/8" long, 1 3/8" wide, 1 5/16" across the inside of the clamp area, and they weigh 3 1/4 oz unboxed. Not signed as to the maker, these ain't Stanley No. 1's unless they changed the base area at some point and didn't bother to tell me. These are in decent condition and were cleaned. There is some wear to the finish but most of it is there. The screws that lock these to the level are good and the sight window and reference line are good, These ain't the fanciest but these guys sure don't show up very often. $24.00 http://oldetoolshop.com/forsale/july/levelsights0701a.jpg http://oldetoolshop.com/forsale/july/levelsights0701b.jpg http://oldetoolshop.com/forsale/july/levelsights0701c.jpg Buck Brothers 1/4 Inch Gouge. Measuring 4 9/16" from the edge to the top of the handle, the blade is 3 3/8" long, 1/4" wide across the inside of the sweep, this is 9 1/2" overall, and this weighs 2 oz unboxed. This is in decent condition overall and was cleaned. Inside of the sweep is good other than some very light frosting. The back is good for the first half and could be used if you wanted to flip the bevel, after that there is some light stuff. The handle is the original one. That has some wear, staining and there is some chipping at the striking end, but it's solid enough. This ain't pretty or perfect but it will get the job done. $15.00 http://oldetoolshop.com/forsale/july/chisel0705a.jpg http://oldetoolshop.com/forsale/july/chisel0705b.jpg Vintage Sargent 8 Inch Steel Wing Compass Or Divider. Measuring 8 1/2" long and this weighs 5 oz unboxed. This is in reasonably good condition and was cleaned. There is a little patina there and here, mostly on the insides of the arms where the wing is located. The joint is good and the locking screw and fine adjustment nut both work. The tips are sharp and good to go. These guys were mainly made for trade schools but it is a good working tool. $18.00 http://oldetoolshop.com/forsale/july/divider0701a.jpg http://oldetoolshop.com/forsale/july/divider0701b.jpg http://oldetoolshop.com/forsale/july/divider0701c.jpg Old Hand Forged Farrier Ball Jaw Blacksmith Tongs. Measuring 14 1/4" long, the jaws are 1 3/8" deep, 1 1/8" wide, and this weighs 1 lb 9 3/4 oz unboxed. Not signed as to the maker. This is in decent condition and was cleaned (oh yeah!) There is some overall pitting. The jaws are good other than the patina. They don't close down tight but that could be fixed by adjusting the handles a little (which is best done with a little heat). The joint has some wiggle but it ain't gonna fall again. The handles are good. This ain't the prettiest but it will get the job done. $22.00 http://oldetoolshop.com/forsale/july/blacksmith0704a.jpg http://oldetoolshop.com/forsale/july/blacksmith0704b.jpg http://oldetoolshop.com/forsale/july/blacksmith0704c.jpg Early Hand Forged Small Face Blacksmith Flatter. Measuring 8 7/8" overall, the head is 2 11/16" long, the face is 1 5/8" wide, 1 1/2" high, and this weighs 1 lb 5 oz unboxed. Not signed as to the maker. This is in decent condition and was cleaned. There is lots of patina on the head (that's how I know it's early eh?) The face has some dings, mushrooming on the sides, and is slightly rounded from wear. The striking end has some chips, a little mushrooming, and I did zing off one sharp bit on the one corner. The handle is old and has the usual stains and a couple of long dead worm holes. That is just shoved into the eye and the head wiggles a little, but it's better than no handle (unless you want a 2ft one..) This ain't minty but it does have some serious age to it and it sure ain't ready for the scrap pile just yet. $26.00 http://oldetoolshop.com/forsale/july/blacksmith0702a.jpg http://oldetoolshop.com/forsale/july/blacksmith0702b.jpg http://oldetoolshop.com/forsale/july/blacksmith0702c.jpg http://oldetoolshop.com/forsale/july/blacksmith0702d.jpg Colwell Cooperage Co Nantucket Style Coopers Hoop Driver. Measuring 10 5/8" overall, the head is 5 1/16" long, the face is 1 1/16" in diameter, the driver is 1 7/16" high, 3/16" wide across the outside, and this weighs 1 lb 8 3/4 oz unboxed. The Colwell Cooperage Co is listed as being in Jersey City NJ, and New York City (this has the New York mark). There isn't much as far as working dates, I see some stuff from the early 1900's up to the 1920s. This is in reasonably good condition for the age and use and was cleaned. There are some pitted spots on the head but overall that is good. The top has some marks from being knocked back on the handle. The face has some dings but it's not as bashed up as a lot of these guys that you see. The driver groove has some dings on the edges but it's still deep enough to use. The handle is old and probably the original one. That has some stains and age checks but it feels solid. The head is loose but ain't gonna come off. These guys sure don't show up much at all by this maker. The last photo has the Colwell catalog page section for this tool, just in case any of you "experts" want to tell me it's a blacksmith tool. Just saying. $35.00 http://oldetoolshop.com/forsale/july/cooperstool0701a.jpg http://oldetoolshop.com/forsale/july/cooperstool0701b.jpg http://oldetoolshop.com/forsale/july/cooperstool0701c.jpg http://oldetoolshop.com/forsale/july/cooperstool0701d.jpg Early Hand Forged Ball Peen Hammer. Measuring 12 3/16" overall, the head is 4 1/4" long, the face is 15/16" wide, 7/8" high, the peen is 1" in diameter, and this weighs 1 lb 2 3/4 oz unboxed. Not signed as to the maker. This is in reasonably good condition and was cleaned. There ain't much in the way of patina on the head. The face and peen have some tiny dings but nothing too bad there. The handle was put on by someone else and they left some scuff marks on the top of the eye. The handle has a few stains but it's solid and on tight. I gotta say, that I sure don't see too many of these old dawgs around in this kind of shape. $24.00 http://oldetoolshop.com/forsale/july/hammer0701a.jpg http://oldetoolshop.com/forsale/july/hammer0701b.jpg http://oldetoolshop.com/forsale/july/hammer0701c.jpg Vintage James Swan Timber Framer T-Auger Handle. Measuring 14 7/8" long and this weighs 1 lb 6 1/4 oz unboxed. This is in decent condition and was cleaned. The head has some frosting but nothing too bad patina wise. There is some crusty inside that I couldn't get to. The tang clamp is good, the screw works and was oiled. The handles have some dings, stains, and wear, but they are solid with no cracks. Both of them do unscrew from the head. This ain't minty but it will get the job done. $24.00 http://oldetoolshop.com/forsale/july/augerhandle0701a.jpg http://oldetoolshop.com/forsale/july/augerhandle0701b.jpg http://oldetoolshop.com/forsale/july/augerhandle0701c.jpg http://oldetoolshop.com/forsale/july/augerhandle0701d.jpg Stone Mason Early Hand Forged Bush Dressing Hammer Head. Measuring 5 3/16" long, the one face is 1 5/16" wide, 9/16" high, the other face is 1 3/8" wide, about 1/2" high, and this weighs 1 lb 6 oz unboxed. Not signed as to the maker. This is in decent condition and was cleaned. There is the usual patina found on these tools but nothing too bad. Both faces have a few small chips on the edges and a couple of dings. The ridges on the faces are slightly rounded but that's how this guy was made. The eye is good to go. These guys are sure getting few and far between, at least around these here parts. $22.00 http://oldetoolshop.com/forsale/july/stonetool0701a.jpg http://oldetoolshop.com/forsale/july/stonetool0701b.jpg http://oldetoolshop.com/forsale/july/stonetool0701c.jpg Old Orphan Stanley No 4 Trammel Point With Pencil Holder. This weighs 2 1/4 oz unboxed. This is in reasonably good condition and was cleaned by someone else. The finish on the body is good and the point is also good. The beam screw works and travels the full distance. The pencil screw has a little patina on the threads but that works. I didn't get the other trammel to go with this but you might have one in your junk boxes and together these are very collectible. $15.00 http://oldetoolshop.com/forsale/july/trammelpoint0701a.jpg http://oldetoolshop.com/forsale/july/trammelpoint0701b.jpg http://oldetoolshop.com/forsale/july/trammelpoint0701c.jpg A Set Vintage of 1/8 Inch Steel Number Stamps With Box. This weighs 11 1/4 oz unboxed. These are marked as shown in the picture. The figures are like a Courier font. These are in used but good shape and were not cleaned. The 0 figure has a little wear, the rest are good. The striking ends have a few light dings but nothing too bad there. The box has some staining and a few dings but it's solid. These ain't minty perfect but they sure ain't bad either. $23.00 http://oldetoolshop.com/forsale/july/stampset0701a.jpg http://oldetoolshop.com/forsale/july/stampset0701b.jpg http://oldetoolshop.com/forsale/july/stampset0701c.jpg Early Hand Forged Adze Eye Cross Peen Hammer. Measuring 13 15/16" overall, the head is 4 15/16" long, the face is 1/2" in diameter, the peen is 9/16" wide, and this weighs 12 3/4 oz unboxed. There is a user name stamped on the side of the eye which might be the maker. This is in decent condition overall and was cleaned. The head has some light patina. The face is good other than some scuff marks and was dressed at some point to get rid of some mushrooming around the edge. The peen is good other than some dings. There is a line on the top and underside of the peen but it's not cracked, just something that was left over when this was forged. There is a crack on the lower front edge of the adze style eye but it doesn't run too deep. The oval handle is the original one. That has some dings and stains. The head wiggles a little but it's not going to come off. This is what it is, but these guys sure don't show up very often with the original handle. $22.00 http://oldetoolshop.com/forsale/july/earlyhammer0701a.jpg http://oldetoolshop.com/forsale/july/earlyhammer0701b.jpg http://oldetoolshop.com/forsale/july/earlyhammer0701c.jpg http://oldetoolshop.com/forsale/july/earlyhammer0701d.jpg Vintage Ward 5/16 Inch Firmer Carving Chisel. Measuring 4 1/4" from the edge to the top of the handle, the blade is 3 1/4" long, this is 9 7/16" overall, and this weighs 2 3/4 oz unboxed. This has the Ward mark and the Ward & Payne trademark. This is in reasonably good condition and was cleaned. The back has some frosting and staining but nothing too bad. The front also has some light patina. The edge has a few small chips but this will need a sharping anyways. The handle is good other than a few light dings and stains and a couple of dings on the end leather washer. This is a quality English edge tool. $17.00 http://oldetoolshop.com/forsale/july/chisel0702a.jpg http://oldetoolshop.com/forsale/july/chisel0702b.jpg --------------------------------------------- “When you're at the end of your rope, tie a knot and hold on.” Theodore Roosevelt Tony Olde River Hard Goods http://www.oldetoolshop.com TSMusic on Facebook http://www.facebook.com/tonyseomusic
266114	<gtgrouch@r...>	2018‑07‑16	Re: FS: July Jewels List B
Tony, I'd like the saw files, if they're not already gone. I'm still looking for a wood-bodied spoke shave that is not functional but can be used as a display piece. Do you gave anything that is too far gone to sell or repair, but that shows what the tools are like? Thanks, Gary Katsanis 228 N Main St Albion, NY 14411 ---- Anthony Seo via OldTools wrote: ============= Summer is in full bloom. There are a bunch of fresh goodies on the list and some good stuff in the NOS section. There ain't an infinite supply of these items so don't wait. PayPal is now accepted and preferred (if you use it) on all items. On items less than $25 (not including shipping) I would appreciate you using the Send Money to Family & Friends option so I don't get killed with the fees but that is your call. Checks and money orders are still welcome, it just seems that 1st Class letters seem to be taking forever to get from there to here. And remember........da more ya buy, the cheaper they fly! First contact (that is e-mail, or phone) that says I want it gets it. Oldtools terms, except on items and orders over $100, if I don't know ya or haven't done business in the past (and my records good way back..) then it's pre-pay. I do take PayPal (except as noted). Prices do not include shipping. All items are shipped with Delivery Confirmation. Insurance, unless it is a big order or a very fragile item is optional. Just let me know. Also, I am shipping a lot more stuff via First Class mail. There will be a small amount added to the shipping cover the cost of the padded mailer. I don't get them for free. Please put your name and address in the message. Saves time and email traffic! --------------------------------------------------- Tyzack Turner No 660 Talisman 24 Inch 7 PT Cross Cut Saw NOS Quality Tool Tyzack Turner No 660 Talisman 24 Inch 7 PT Cross Cut Saw. This weighs 1 lb 9 oz unboxed. This is NOS, that's New Old Stock, and was not cleaned. There ain't nothing at all to fuss about with this guy. The blade is shiny and sharp. There is a little bit of the protective coating showing at the toe. The tote and saw nuts are as good as they get. This is a quality tool made by an well respected English saw maker and I have been selling and shipping saws now for over 24 years so I know what I'm talking about. $45.00 http://oldetoolshop.com/forsale/july/saw0701a.jpg http://oldetoolshop.com/forsale/july/saw0701b.jpg http://oldetoolshop.com/forsale/july/saw0701c.jpg http://oldetoolshop.com/forsale/july/saw0701d.jpg http://oldetoolshop.com/forsale/july/saw0701e.jpg Tyzack Turner No 166 Talisman 10 Inch 13 PT Tenon Saw. This weighs 1 lb 3 1/2 oz unboxed. This is NOS, that's New Old Stock, and was not cleaned. There are some spots of funky on the brass back from being stored but the blade is factory bright. The handle finish is perfect. There also is a little funky on the one sawnut on the front and some on the nuts on the back, (these weren't stored in a very nice place.) Nothing worth kicking the cat over. If you are looking for a top quality back saw, you can't do much better than this for the price. $60.00 http://oldetoolshop.com/forsale/june/saw0606a.jpg http://oldetoolshop.com/forsale/june/saw0606b.jpg http://oldetoolshop.com/forsale/june/saw0606c.jpg http://oldetoolshop.com/forsale/june/saw0606d.jpg NOS Tyzack Sons & Turner No 130 8 Inch Gentleman's Brass Back Dovetail Saw. Measuring 12 13/16" overall, the blade is 8" long, 1 9/16" high (from the teeth to the start of the back), this is sharpened to 15 PT (14 TPI) CC, and this weighs 5 1/4 oz unboxed. This is NOS (that's New Old Stock) and was not cleaned. There is nothing to fuss about at all other than a few very light scuffs to the finish on the blade. This is factory sharp and straight and they don't get any better than this. $24.00 http://oldetoolshop.com/forsale/july/saw0702a.jpg http://oldetoolshop.com/forsale/july/saw0702b.jpg Tyzack Sons & Turner No 131 8 Inch Gentleman's Steel Back Dovetail Saw. Measuring 12 13/16" overall, the blade is 8" long, 1 9/16" high (from the teeth to the start of the back), this is sharpened to 15 PT (14 TPI) CC, and this weighs 5 1/4 oz unboxed. This is NOS (that's New Old Stock) and was not cleaned. There is nothing to fuss about at all other than a little bit of extra protective finish on the front of the blade. This is factory sharp and straight and they don't get any better than this. $20.00 http://oldetoolshop.com/forsale/may/saw0503a.jpg http://oldetoolshop.com/forsale/may/saw0503b.jpg Ridgway No 220 11 Piece Irwin Pattern Auger Bit Set & Roll. The sizes are run from 1/4" to 1", and this all weighs 3 lbs 1/2 oz unboxed. Ridgway was a long time Sheffield England auger bit maker in business from 1878 until they merged with Record in 1975 to become Record Ridgway. These just have the Ridgway marks so they were made before that time. These are NOS, that's New Old Stock. Note these are straight, any bending you see is because of camera lens distortion. I did clean off a few small spots of rust they picked up from setting around. The edges, lead screws, and tangs are factory fresh. The canvas roll does have a couple of rust stains on the inside and a little bit of musty smell to it, but it just needs a good airing out. If you are looking for a quality set of bits, well you can't do much better than this one. $55.00 http://oldetoolshop.com/forsale/july/bracebitset0701a.jpg http://oldetoolshop.com/forsale/july/bracebitset0701b.jpg http://oldetoolshop.com/forsale/july/bracebitset0701c.jpg http://oldetoolshop.com/forsale/july/bracebitset0701d.jpg Rabone Chesterman 10 Inch Sweep Brace. This weighs 2 lbs 12 1/4 oz unboxed. The Rabone and Chesterman companies merged in 1963 and were in business until 1989 when Stanley bought the firm. This is NOS, that's New Old Stock, and was not cleaned. There is a touch of patina there and there from setting around but nothing too bad. The grip and pad are plastic and they have a few dings. The ratchet and jaws are good, although it could stand a touch of oil. This ain't the fanciest but this is a good heavy duty brace. Note: I also have an 8" sweep one available at the same price. $24.00 http://oldetoolshop.com/forsale/july/brace0701a.jpg http://oldetoolshop.com/forsale/july/brace0701b.jpg http://oldetoolshop.com/forsale/july/brace0701c.jpg http://oldetoolshop.com/forsale/july/brace0701d.jpg Four Marples Blue Chip Paring Bench Chisels. Left to right, there is a 1/4", a 3/8", a 1/2", a 3/4", and they weigh 1 lb 4 1/2 oz unboxed. These are NOS (that's New Old Stock) and were not cleaned. Note: these are straight, any bending you see is because of camera lens distortion. There is little light funky and couple have some light rust spots from laying around but nothing worth kicking the cat over. The handles have some scuffs from being knocked around. Note: The ones you get might vayu slightly from the pictures. These are quality chisels by one of England's top tool makers. $52.00 http://oldetoolshop.com/forsale/june/chiselset0603a.jpg http://oldetoolshop.com/forsale/june/chiselset0603b.jpg http://oldetoolshop.com/forsale/june/chiselset0603c.jpg Stanley No 12-331 9 1/2 Block Plane Blade. This weighs 2 1/2 oz unboxed. This is NOS, that's New Old Stock and was made in merry olde England. They don't get much better than this. It sure can't hurt to have a spare. $15.00 http://oldetoolshop.com/forsale/july/planeblade0701a.jpg http://oldetoolshop.com/forsale/july/planeblade0701b.jpg NOS Stanley England 12-315 2 3/8 Inch Plane Blade. This weighs 5 1/2 oz unboxed. This will fit the No. 4 1/2, 5 1/2, 6, and 7 planes except for the very early models that had a narrower blade. This is NOS (that's New Old Stock) still in the retail packaging. They don't get any better than this. $30.00 http://oldetoolshop.com/forsale/june/planeblade0601a.jpg http://oldetoolshop.com/forsale/june/planeblade0601b.jpg NOS Stanley England 12-313 2 Inch Plane Blade. This weighs 4 3/4 oz unboxed. This will fit the No. 4 and 5 planes. This is NOS (that's New Old Stock) still in the retail packaging. They don't get any better than this. $20.00 http://oldetoolshop.com/forsale/june/planeblade0602a.jpg http://oldetoolshop.com/forsale/june/planeblade0602b.jpg Two Lufkin Machinist No 40 Series Calipers. On the left is a 3" No. 41 outside caliper, on the right is a 4" No. 42 inside caliper, and they weigh 2 1/2 oz unboxed. These are NOS, that's New Old Stock. I did clean off some oil residue on these (they were oiled at the factory). There is a little still up in the joints and there and here. The tips of both of them have a few stained spots (these weren't stored very well). Lufkin machinist tools are every bit as good as their Starrett and Brown & Sharpe cousins. $20.00 http://oldetoolshop.com/forsale/june/machinisttool0612a.jpg http://oldetoolshop.com/forsale/june/machinisttool0612b.jpg http://oldetoolshop.com/forsale/june/machinisttool0612c.jpg Fine Products England Tool Chisel Roll With 8 Pockets. Measuring 19 3/4" long, 14 3/8" high, the pockets vary in width from 1 1/2" to 2 1/2" wide, and this weighs 9 oz unboxed. Made by the H. L. Fine and Son Ltd company of Middlesex England. This is NOS, that's New Old Stock. This was never out of the package until I took it out to take the pretty pictures. Canvas on the outside and some kind of felting on the inside. This is a well made and quality item. $18.00 http://oldetoolshop.com/forsale/june/toolroll0601a.jpg http://oldetoolshop.com/forsale/june/toolroll0601b.jpg http://oldetoolshop.com/forsale/june/toolroll0601c.jpg Two Cabinetmakers Shave Hooks Or Shavehooks. These are 7 5/16" long, the triangle blade is 2 7/16" across the edges, the other one is 2 3/8" high, 1 3/4" wide, and they weigh 9 3/4 oz unboxed. Not signed as to the maker, but I know for a fact that these came over from England in the 1980's. These are NOS, that's New Old Stock. But they have been bouncing around boxes for a while. I did clean some light patina off of the shafts and a few small spots on the blades. The edges had a few light dings that I fixed with some file work. The handle finish is good on both. These are quality and handy tools. $15.00 http://oldetoolshop.com/forsale/july/shavehook0702a.jpg http://oldetoolshop.com/forsale/july/shavehook0702b.jpg http://oldetoolshop.com/forsale/july/shavehook0702c.jpg Seven Nicholson 5 Inch Taper Files. The upper 5 are marked Dbl Ex Slim Taper, the lower 2 are marked Slim Taper, they measure 5 1/4" along the sides across the teeth and these weigh 6 1/4 oz unboxed. These are NOS (that's New Old Stock). I did take some rust off of the tangs and a couple of the tops. There are a few light spots of rust on the teeth but these are like 99% clean. These are the ones to have for sharpening saws, especially the smaller tooth sized ones, and ya sure ain't gonna walk into the local hardware store and purchase files of this quality at this kind of price. $35.00 http://oldetoolshop.com/forsale/july/files0702a.jpg http://oldetoolshop.com/forsale/july/files0702b.jpg http://oldetoolshop.com/forsale/july/files0702c.jpg http://oldetoolshop.com/forsale/july/files0702d.jpg Working & Collectible Old Tools Three Millers Falls No 30 Chisels. The first one is a 3/4", the blade is 2 15/16", the middle one is a 1", the blade is 3" long, the last one is a 1 1/2", the blade is 3", and they weigh 1 lb 7 oz unboxed. These are in used but reasonably good condition and were cleaned. The blades have couple of dots on the back and the fronts but nothing too bad at all. The edges are good and sharp or pretty darn close. The red Permaloid handles have some scuffs and light wear and somebody drilled hanging holes so you won't have to do it. The striking button on the 3/4" is banged up a bit, the other two are good. These ain't perfect but they sure ain't bad either and most of these I see look like Buck Rogers built two spaceships with them. Just saying. $50.00 http://oldetoolshop.com/forsale/july/chiselset0701a.jpg http://oldetoolshop.com/forsale/july/chiselset0701b.jpg http://oldetoolshop.com/forsale/july/chiselset0701c.jpg http://oldetoolshop.com/forsale/july/chiselset0701d.jpg http://oldetoolshop.com/forsale/july/chiselset0701e.jpg Set Of Stanley No 71 Router Plane Parts. There are the knobs and threaded rods, the blade clamp, a 9/16" blade, and this all weighs 7 oz unboxed. These are all in used condition and were cleaned. The knobs are the painted hardwood variety and were refinished. That ain't a perfect job but they are better than they were. There are some dings and the one has a partial check along the side. The nuts on the rods have a little wear to the plating on the tops but they remove from the rods. The blade clamp has a little roughness to the plating and some light patina inside but it's solid. The plating on the thumbscrew is worn and there is a little pitting but the threads are good. The blade does have some light pitting on the cutting face and some deeper stuff on the sides of the shaft. These ain't minty perfect and they sure ain't got a minty perfect price tag but decent parts are better than no parts, eh? Note: I do not have any of the other parts for this plane. $55.00 http://oldetoolshop.com/forsale/july/planepart0701a.jpg http://oldetoolshop.com/forsale/july/planepart0701b.jpg http://oldetoolshop.com/forsale/july/planepart0701c.jpg http://oldetoolshop.com/forsale/july/planepart0701d.jpg A J Wilkinson 8 Inch Folding Handle Drawknife. Measuring 16 1/8" overall, the blade is 8 1/4" long (straight across), 1 1/2" or better wide across the edge, and this weighs 1 lb 9 3/4 oz unboxed. John G. Young of Hyde Park, MA was granted Pat. No. 542,721 on July. 16, 1895 for the design of this tool which was made by A. J. Wilkinson & Co. of Boston, MA. This is in decent condition and was cleaned. The back of the blade has some light pitting right at the edge and some frosting and spots on the rest but that is good for the most part. I did run a file over some mushrooming on the back and there are some dings on the top. The edge is fairly sharp as is. The front has some spots of pitting. The handles were refinished, that ain't a perfect job but they are better than they were. The plating on the handle arms is worn. Both nuts work and the screws do remove. This ain't minty but it will get the job done. $50.00 http://oldetoolshop.com/forsale/july/drawknife0701a.jpg http://oldetoolshop.com/forsale/july/drawknife0701b.jpg http://oldetoolshop.com/forsale/july/drawknife0701c.jpg http://oldetoolshop.com/forsale/july/drawknife0701d.jpg Early Stanley No 62 Marking Gage. This weighs 4 oz unboxed. This isn't marked other than the patent date but these guys rarely were. Good ole Justus A. Traut of New Britain, CT was granted Pat. No. 334,308 on Jan. 12, 1886 for the design of the fence used on this tool. Figuring 20 years for the use of the patent date, that puts this guy between 112 and 132 years old. This is in reasonably good condition and was cleaned by someone else. He also hit it with the shiny stuff. The beam has some dings from the screw and a few stains but nothing too bad in that department. The head also has a few light dings and stains. The locking screw is good. The screw for the point does remove and the point removes as well. That could stand a quick sharpening but there is lots to work with. This ain't pristine but having seen my share of marking gages over the years, these guys rarely are when they get to be this old. $23.00 http://oldetoolshop.com/forsale/july/markinggage0701a.jpg http://oldetoolshop.com/forsale/july/markinggage0701b.jpg http://oldetoolshop.com/forsale/july/markinggage0701c.jpg http://oldetoolshop.com/forsale/july/markinggage0701d.jpg Vintage Meier Germany 13/16 Inch Barbers Straight Razor. The blade is 2 7/8" long across the edge, 13/16" wide across the edge, and this weighs 1 1/2 oz unboxed. This is in reasonably good condition and was not cleaned. There are some dots of rust on both sides of the blade but nothing too bad. There is a spot on the top as well. The edge is good with no nicks but it could stand a sharpening. The handle scales look to be celluloid. Those are good other than a few light scuffs. The joint is a little loose as is the spacer at the end of the handle scales. This ain't perfect but these wider bladed models sure don't show up every day. $30.00 http://oldetoolshop.com/forsale/july/razor0701a.jpg http://oldetoolshop.com/forsale/july/razor0701b.jpg http://oldetoolshop.com/forsale/july/razor0701c.jpg L S Starrett No 38 24 Inch Lock Joint Outside Calipers. Measuring 24 13/16" from the tips to the top of the joint and and this weighs 2 lbs 9 3/4 oz unboxed. This is in decent condition overall. It was cleaned by someone else. There are some spots of light pitting and frosting, mostly on the front of the arms The joint lock works as does the fine adjustment. The tips are good with no wear. This ain't minty but price a new one without the lock joint and this is a real deal. $80.00 http://oldetoolshop.com/forsale/june/machinisttool0615a.jpg http://oldetoolshop.com/forsale/june/machinisttool0615b.jpg http://oldetoolshop.com/forsale/june/machinisttool0615c.jpg http://oldetoolshop.com/forsale/june/machinisttool0615d.jpg Hand Forged Early Closed End Single Handle Scorp. Measuring 11 1/8" overall, the head is 1 7/8" wide, 1 3/8" high, the cutting area is about 1" wide at the ends, 15/16" at the center, and this weighs 7 1/4 oz unboxed. Not signed as to the maker. This is in decent condition overall and was cleaned. The cutting area has some very light pitting but nothing too bad. There is a ding on he edge but this guy is fairly sharp. There is some patina inside the head and on the upper areas and the tang. The handle is the original one. That has some stains and wear and there is a thin check at the top. I did reseat the hand forged iron ring that acts as ferrule, but that might loosen up again. This ain't pretty or perfect but it is a good working tool. $45.00 http://oldetoolshop.com/forsale/june/earlyscrop0601a.jpg http://oldetoolshop.com/forsale/june/earlyscrop0601b.jpg http://oldetoolshop.com/forsale/june/earlyscrop0601c.jpg Keen Kutter 1/2 Inch Paring Or Bevel Edge Firmer Chisel. Measuring 8 5/8" from the edge to the end of the socket, the blade is 6 3/16" long, this is 12 1/8" overall, and this weighs 4 1/2 oz unboxed. This is in reasonably good condition and was cleaned. The back has some very light frosting and rust etching but nothing deep at all. The front is good other than some staining and there are user initials after the mark. The socket is good but the blade does angle down a little looking from the side. The handle is a replacement. That is good other than a few stains. This ain't minty but it sure ain't bad and it's got a whole lot of blade to work with. $19.00 http://oldetoolshop.com/forsale/july/chisel0706a.jpg http://oldetoolshop.com/forsale/july/chisel0706b.jpg M Myers & Son England Brass Protractor. Measuring 3 11/16" long, 1 15/16" high, and this weighs 1/2 oz unboxed. M Myers & Son were long time English makers of pens and drafting tools. This is in reasonably good condition and was cleaned. The front is good and all the rulings are readable. They are stamped and not just inked on. The back has a few stained spots but nothing too bad. This is a quality tool, unlike the plastic ones you get today. $18.00 http://oldetoolshop.com/forsale/july/draftingtool0702a.jpg http://oldetoolshop.com/forsale/july/draftingtool0702b.jpg http://oldetoolshop.com/forsale/july/draftingtool0702c.jpg L S Starrett No 160 Machinist Toolmaker Clamp Or Vise. This weighs 6 1/2 oz unboxed. This is in decent condition and was cleaned. There is some light patina including some vice jaw marks on the sides. The jaw faces are good, this only has the thin jaw. The screw threads are good and it travels the full distance. The head has some scuffs and wear to the cross hatching. The base also has some scuffs and wear. This ain't pretty or perfect and it sure ain't got the price tag of a minty one but it will get the job done. $18.00 http://oldetoolshop.com/forsale/july/machinisttool0706a.jpg http://oldetoolshop.com/forsale/july/machinisttool0706b.jpg http://oldetoolshop.com/forsale/july/machinisttool0706c.jpg L S Starrett No 466 A Micrometer Depth Gage. This weighs 2 1/2 oz unboxed. Good old Laroy S. Starrett of Athol, MA was granted Pat. No. 726,003 on April 21, 1903 for the design of this tool. This is in good shape and was lightly cleaned. There ain't much in the way of patina to fuss about. There are some light stained spots on the sides of the base but the working face is good. The micrometer scales are clean and readable and this turns freely. The locking nut for the rod at the top also works and the rod removes. For a tool that is over 100 years old (figuring the 20 year limit on patent date markings), this one is right nice. $28.00 http://oldetoolshop.com/forsale/july/machinisttool0705a.jpg http://oldetoolshop.com/forsale/july/machinisttool0705b.jpg http://oldetoolshop.com/forsale/july/machinisttool0705c.jpg L S Starrett No 166 Machinist Pin Vise. This weighs 1 oz unboxed. There is no size mark but it looks to be a B. This is in used but reasonably good condition and was not cleaned. The chuck and jaws are good. There is a user name on the top of the chuck. The hard rubber handle is a little discolored and has a few dings but that is good to go. This ain't pristine but it will get the job done. $14.00 http://oldetoolshop.com/forsale/july/machinisttool0702a.jpg http://oldetoolshop.com/forsale/july/machinisttool0702b.jpg Craftsman No 5513 Spiral Tapered Brace Reamer. Measuring 4 3/8" long, 2" in diameter at the top, and this weighs 6 oz unboxed. These is in used but reasonably good condition and was not cleaned. There are some spots of rust on the insides of the flutes but the edges are good other than some very tiny dings. The tang also has some dings but nothing too bad there. This ain't minty but it will get the job done and it is a must have tool for cleaning mushrooming out of the insides of chisel sockets. I have several here that I use all the time. $17.00 http://oldetoolshop.com/forsale/july/bracetool0701a.jpg http://oldetoolshop.com/forsale/july/bracetool0701b.jpg Millers Falls No 214 Saw Set Or Sawset. This weighs 1 lb 4 oz unboxed. This isn't marked but it is a 214 with the Sears paint job. Identical tool, slightly different color scheme. This is in used but reasonably good shape and was cleaned. This has all of the original finish but there is some staining mainly on the front handle. The plunger tip is good and the anvil doesn't show much in the way of wear. That is marked from 4 to 16 as far as TPI goes. The screw on that works and was oiled as was the fence screw. This ain't the fanciest, but for the money, it sure ain't bad. $20.00 http://oldetoolshop.com/forsale/july/sawset0701a.jpg http://oldetoolshop.com/forsale/july/sawset0701b.jpg http://oldetoolshop.com/forsale/july/sawset0701c.jpg Millers Falls No 206 Steel Body Block Plane. This weighs 1 lb 1/4 oz unboxed. This model was made between 1940 and 1959. This is in used but reasonably good condition and was cleaned. Note this is straight, any bending you see is because of camera lens distortion, although why folks would think that I would sell a bent plane is beyond me. The sides have some frosting and a few dings. The sole also has some frosting and some scratches but nothing too there. The body finish is original and close to perfect other than some dings on the tops of the sides and at the heel. The cap is good. The blade is clean other than some scratches on the cutting face and there is lots to work with. The blade will need a sharpening. All the screws work and were oiled. This ain't minty perfect but seeing as how most of these went to trade schools, well this one sure is better than most of them that show up. $22.00 http://oldetoolshop.com/forsale/july/millersfalls2060701a.jpg http://oldetoolshop.com/forsale/july/millersfalls2060701b.jpg http://oldetoolshop.com/forsale/july/millersfalls2060701c.jpg http://oldetoolshop.com/forsale/july/millersfalls2060701d.jpg Two Vintage Wooden Level Sights. They measure 1 7/8" long, 1 3/8" wide, 1 5/16" across the inside of the clamp area, and they weigh 3 1/4 oz unboxed. Not signed as to the maker, these ain't Stanley No. 1's unless they changed the base area at some point and didn't bother to tell me. These are in decent condition and were cleaned. There is some wear to the finish but most of it is there. The screws that lock these to the level are good and the sight window and reference line are good, These ain't the fanciest but these guys sure don't show up very often. $24.00 http://oldetoolshop.com/forsale/july/levelsights0701a.jpg http://oldetoolshop.com/forsale/july/levelsights0701b.jpg http://oldetoolshop.com/forsale/july/levelsights0701c.jpg Buck Brothers 1/4 Inch Gouge. Measuring 4 9/16" from the edge to the top of the handle, the blade is 3 3/8" long, 1/4" wide across the inside of the sweep, this is 9 1/2" overall, and this weighs 2 oz unboxed. This is in decent condition overall and was cleaned. Inside of the sweep is good other than some very light frosting. The back is good for the first half and could be used if you wanted to flip the bevel, after that there is some light stuff. The handle is the original one. That has some wear, staining and there is some chipping at the striking end, but it's solid enough. This ain't pretty or perfect but it will get the job done. $15.00 http://oldetoolshop.com/forsale/july/chisel0705a.jpg http://oldetoolshop.com/forsale/july/chisel0705b.jpg Vintage Sargent 8 Inch Steel Wing Compass Or Divider. Measuring 8 1/2" long and this weighs 5 oz unboxed. This is in reasonably good condition and was cleaned. There is a little patina there and here, mostly on the insides of the arms where the wing is located. The joint is good and the locking screw and fine adjustment nut both work. The tips are sharp and good to go. These guys were mainly made for trade schools but it is a good working tool. $18.00 http://oldetoolshop.com/forsale/july/divider0701a.jpg http://oldetoolshop.com/forsale/july/divider0701b.jpg http://oldetoolshop.com/forsale/july/divider0701c.jpg Old Hand Forged Farrier Ball Jaw Blacksmith Tongs. Measuring 14 1/4" long, the jaws are 1 3/8" deep, 1 1/8" wide, and this weighs 1 lb 9 3/4 oz unboxed. Not signed as to the maker. This is in decent condition and was cleaned (oh yeah!) There is some overall pitting. The jaws are good other than the patina. They don't close down tight but that could be fixed by adjusting the handles a little (which is best done with a little heat). The joint has some wiggle but it ain't gonna fall again. The handles are good. This ain't the prettiest but it will get the job done. $22.00 http://oldetoolshop.com/forsale/july/blacksmith0704a.jpg http://oldetoolshop.com/forsale/july/blacksmith0704b.jpg http://oldetoolshop.com/forsale/july/blacksmith0704c.jpg Early Hand Forged Small Face Blacksmith Flatter. Measuring 8 7/8" overall, the head is 2 11/16" long, the face is 1 5/8" wide, 1 1/2" high, and this weighs 1 lb 5 oz unboxed. Not signed as to the maker. This is in decent condition and was cleaned. There is lots of patina on the head (that's how I know it's early eh?) The face has some dings, mushrooming on the sides, and is slightly rounded from wear. The striking end has some chips, a little mushrooming, and I did zing off one sharp bit on the one corner. The handle is old and has the usual stains and a couple of long dead worm holes. That is just shoved into the eye and the head wiggles a little, but it's better than no handle (unless you want a 2ft one..) This ain't minty but it does have some serious age to it and it sure ain't ready for the scrap pile just yet. $26.00 http://oldetoolshop.com/forsale/july/blacksmith0702a.jpg http://oldetoolshop.com/forsale/july/blacksmith0702b.jpg http://oldetoolshop.com/forsale/july/blacksmith0702c.jpg http://oldetoolshop.com/forsale/july/blacksmith0702d.jpg Colwell Cooperage Co Nantucket Style Coopers Hoop Driver. Measuring 10 5/8" overall, the head is 5 1/16" long, the face is 1 1/16" in diameter, the driver is 1 7/16" high, 3/16" wide across the outside, and this weighs 1 lb 8 3/4 oz unboxed. The Colwell Cooperage Co is listed as being in Jersey City NJ, and New York City (this has the New York mark). There isn't much as far as working dates, I see some stuff from the early 1900's up to the 1920s. This is in reasonably good condition for the age and use and was cleaned. There are some pitted spots on the head but overall that is good. The top has some marks from being knocked back on the handle. The face has some dings but it's not as bashed up as a lot of these guys that you see. The driver groove has some dings on the edges but it's still deep enough to use. The handle is old and probably the original one. That has some stains and age checks but it feels solid. The head is loose but ain't gonna come off. These guys sure don't show up much at all by this maker. The last photo has the Colwell catalog page section for this tool, just in case any of you "experts" want to tell me it's a blacksmith tool. Just saying. $35.00 http://oldetoolshop.com/forsale/july/cooperstool0701a.jpg http://oldetoolshop.com/forsale/july/cooperstool0701b.jpg http://oldetoolshop.com/forsale/july/cooperstool0701c.jpg http://oldetoolshop.com/forsale/july/cooperstool0701d.jpg Early Hand Forged Ball Peen Hammer. Measuring 12 3/16" overall, the head is 4 1/4" long, the face is 15/16" wide, 7/8" high, the peen is 1" in diameter, and this weighs 1 lb 2 3/4 oz unboxed. Not signed as to the maker. This is in reasonably good condition and was cleaned. There ain't much in the way of patina on the head. The face and peen have some tiny dings but nothing too bad there. The handle was put on by someone else and they left some scuff marks on the top of the eye. The handle has a few stains but it's solid and on tight. I gotta say, that I sure don't see too many of these old dawgs around in this kind of shape. $24.00 http://oldetoolshop.com/forsale/july/hammer0701a.jpg http://oldetoolshop.com/forsale/july/hammer0701b.jpg http://oldetoolshop.com/forsale/july/hammer0701c.jpg Vintage James Swan Timber Framer T-Auger Handle. Measuring 14 7/8" long and this weighs 1 lb 6 1/4 oz unboxed. This is in decent condition and was cleaned. The head has some frosting but nothing too bad patina wise. There is some crusty inside that I couldn't get to. The tang clamp is good, the screw works and was oiled. The handles have some dings, stains, and wear, but they are solid with no cracks. Both of them do unscrew from the head. This ain't minty but it will get the job done. $24.00 http://oldetoolshop.com/forsale/july/augerhandle0701a.jpg http://oldetoolshop.com/forsale/july/augerhandle0701b.jpg http://oldetoolshop.com/forsale/july/augerhandle0701c.jpg http://oldetoolshop.com/forsale/july/augerhandle0701d.jpg Stone Mason Early Hand Forged Bush Dressing Hammer Head. Measuring 5 3/16" long, the one face is 1 5/16" wide, 9/16" high, the other face is 1 3/8" wide, about 1/2" high, and this weighs 1 lb 6 oz unboxed. Not signed as to the maker. This is in decent condition and was cleaned. There is the usual patina found on these tools but nothing too bad. Both faces have a few small chips on the edges and a couple of dings. The ridges on the faces are slightly rounded but that's how this guy was made. The eye is good to go. These guys are sure getting few and far between, at least around these here parts. $22.00 http://oldetoolshop.com/forsale/july/stonetool0701a.jpg http://oldetoolshop.com/forsale/july/stonetool0701b.jpg http://oldetoolshop.com/forsale/july/stonetool0701c.jpg Old Orphan Stanley No 4 Trammel Point With Pencil Holder. This weighs 2 1/4 oz unboxed. This is in reasonably good condition and was cleaned by someone else. The finish on the body is good and the point is also good. The beam screw works and travels the full distance. The pencil screw has a little patina on the threads but that works. I didn't get the other trammel to go with this but you might have one in your junk boxes and together these are very collectible. $15.00 http://oldetoolshop.com/forsale/july/trammelpoint0701a.jpg http://oldetoolshop.com/forsale/july/trammelpoint0701b.jpg http://oldetoolshop.com/forsale/july/trammelpoint0701c.jpg A Set Vintage of 1/8 Inch Steel Number Stamps With Box. This weighs 11 1/4 oz unboxed. These are marked as shown in the picture. The figures are like a Courier font. These are in used but good shape and were not cleaned. The 0 figure has a little wear, the rest are good. The striking ends have a few light dings but nothing too bad there. The box has some staining and a few dings but it's solid. These ain't minty perfect but they sure ain't bad either. $23.00 http://oldetoolshop.com/forsale/july/stampset0701a.jpg http://oldetoolshop.com/forsale/july/stampset0701b.jpg http://oldetoolshop.com/forsale/july/stampset0701c.jpg Early Hand Forged Adze Eye Cross Peen Hammer. Measuring 13 15/16" overall, the head is 4 15/16" long, the face is 1/2" in diameter, the peen is 9/16" wide, and this weighs 12 3/4 oz unboxed. There is a user name stamped on the side of the eye which might be the maker. This is in decent condition overall and was cleaned. The head has some light patina. The face is good other than some scuff marks and was dressed at some point to get rid of some mushrooming around the edge. The peen is good other than some dings. There is a line on the top and underside of the peen but it's not cracked, just something that was left over when this was forged. There is a crack on the lower front edge of the adze style eye but it doesn't run too deep. The oval handle is the original one. That has some dings and stains. The head wiggles a little but it's not going to come off. This is what it is, but these guys sure don't show up very often with the original handle. $22.00 http://oldetoolshop.com/forsale/july/earlyhammer0701a.jpg http://oldetoolshop.com/forsale/july/earlyhammer0701b.jpg http://oldetoolshop.com/forsale/july/earlyhammer0701c.jpg http://oldetoolshop.com/forsale/july/earlyhammer0701d.jpg Vintage Ward 5/16 Inch Firmer Carving Chisel. Measuring 4 1/4" from the edge to the top of the handle, the blade is 3 1/4" long, this is 9 7/16" overall, and this weighs 2 3/4 oz unboxed. This has the Ward mark and the Ward & Payne trademark. This is in reasonably good condition and was cleaned. The back has some frosting and staining but nothing too bad. The front also has some light patina. The edge has a few small chips but this will need a sharping anyways. The handle is good other than a few light dings and stains and a couple of dings on the end leather washer. This is a quality English edge tool. $17.00 http://oldetoolshop.com/forsale/july/chisel0702a.jpg http://oldetoolshop.com/forsale/july/chisel0702b.jpg --------------------------------------------- “When you're at the end of your rope, tie a knot and hold on.” Theodore Roosevelt Tony Olde River Hard Goods http://www.oldetoolshop.com TSMusic on Facebook http://www.facebook.com/tonyseomusic ------------------------------------------------------------------------ OldTools is a mailing list catering to the interests of hand tool aficionados, both collectors and users, to discuss the history, usage, value, location, availability, collectibility, and restoration of traditional handtools, especially woodworking tools. To change your subscription options: https://oldtools.swingleydev.com/mailman/listinfo/oldtools To read the FAQ: https://swingleydev.com/archive/faq.html OldTools archive: https://swingleydev.com/ot/ OldTools@s...