I agree with Scott: the drier the mix the better, as long as it has sufficient
moisture to be completely wet. You want almost no slump. I personally like the
fiberglass admix, but I also use rebar or 6-6-10-10 mesh about two inches up
from the bottom. Once it is cured, there will be virtually no shifting.

Personally, I think 3" is too thin. I usually pour a minimum of 4" and I use 6"
where strength is critical. It's not clear to me whether or not you intend for
this to be movable when completed. If it is to be moved, I would definitely go
with something thicker than 3".

Good luck, Gary Katsanis
Albion New York, USA

---- Claudio DeLorenzi  wrote: 

=============
Hi Guys:
Re: making a base for a metal lathe

I have a cabinet that it rests on, and it's just basically mounted on a
couple of sheets of plywood.  I would rather it be mounted on a rigid base
to permit leveling of the lathe (ie removing twist), preferably some thick
steel plate, but since I can't find any cold rolled plate at a reasonable
cost, I thought why not try some concrete?

  In about 1990, I put some sand and concrete on the shelf beneath an
inexpensive "RecordPower" wood lathe, that really improved performance
(weight, rigidity, and absorbed the harmonics and whatever), and I've read
that the Gingery Lathe guys are using concrete bases for their home foundry
cast aluminum lathes.

  I was hoping that someone on the list had direct experience with doing
this sort of thing, and whether to use simple 9 g ladder wire reinforcement
or integral glass fiber mixed in with the concrete, or whether to use the
"countertop" mixes that have those sorts of things built in, or any other
useful suggestions (esp what NOT to do).

   My thought was to cast about a 3 inch thick base with some cast in place
studs for mounting the lathe.  I would simply lay this slab on top of the
plywood cabinet top, relying on the rigidity of the concrete to hold the
lathe ways flat (after I have taken any twist out with the hold down
bolts).  I'm not sure if concrete "moves" with ambient moisture changes- I
just don't know much about concrete since I have personally only used it to
hold up clotheslines & fenceposts and the occasional small stair landing.

  I did ask for responses off list, so as to not offend those woodworker
only Galoots (even though every single Galoot treasures metal tools, each
tool consisting of parts made either directly or indirectly on a metal
cutting lathe... the several thousand year old mother of all tools).
Claudio

On Fri, Mar 16, 2018 at 11:45 AM, Ed Minch  wrote:

> Stop! You’re both right.  I use a shovel to start and a hoe to maintain
>
> Ed Minch
>
>
>
>
> > On Mar 16, 2018, at 11:21 AM, Michael Suwczinsky 
> wrote:
> >
> > With a shovel!
> >
> > On Thu, Mar 15, 2018 at 4:59 PM, james rich  <mailto:jameslrich3@g...>> wrote:
> >
> >> It is if you mix it with a hoe in a wheelbarrow
>
> ------------------------------------------------------------------------
> OldTools is a mailing list catering to the interests of hand tool
> aficionados, both collectors and users, to discuss the history, usage,
> value, location, availability, collectibility, and restoration of
> traditional handtools, especially woodworking tools.
>
> To change your subscription options:
> https://oldtools.swingleydev.com/mailman/listinfo/oldtools
>
> To read the FAQ:
> https://swingleydev.com/archive/faq.html
>
> OldTools archive: https://swingleydev.com/ot/
>
> OldTools@s...
>
------------------------------------------------------------------------
OldTools is a mailing list catering to the interests of hand tool
aficionados, both collectors and users, to discuss the history, usage,
value, location, availability, collectibility, and restoration of
traditional handtools, especially woodworking tools.

To change your subscription options:
https://oldtools.swingleydev.com/mailman/listinfo/oldtools

To read the FAQ:
https://swingleydev.com/archive/faq.html

OldTools archive: https://swingleydev.com/ot/

OldTools@s...